manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

INSTALLATION

1) If parts have been removed from fuel tank, install them before

installing fuel tank to vehicle.

2) Connect fuel vapor hose and pipe joints to fuel pump assembly,

and clamp vapor hose securely.

CAUTION:
When connecting joint, clean outside surfaces of pipe
where joint is to be inserted, push joint into pipe till
joint lock clicks and check to ensure that pipes are
connected securely, or fuel leak may occur.

3) Install fuel tank to vehicle.

Tightening Torque
(a): 23 N·m (2.3 kg-m, 17.0 lb-ft)

1. Joint
2. Fuel return hose
3. Fuel feed hose
4. Fuel vapor hose
5. Fuel tank
6. Bolt

4) Connect fuel filler hose to filler neck and breather hose to fuel

tank and clamp hoses securely.

Tightening Torque
(b): 1.5 N·m (0.15 kg-m, 1.0 lb-ft)

5) Connect fuel hoses to each pipe and fuel vapor hose to fuel

tank. Refer to 6C-3 for proper connection.

1. Fuel filler hose
2. Breather hose
3. Fuel filler neck
4. Fuel tank

6) Connect fuel pump wire coupler.

1. Fuel pump wire coupler

6C-10

ENGINE FUEL

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

Hama Pico Operating Instructions preview
Pico
Бренд: Hama Страницы: 2
Safe Fleet PRIME DESIGN VRI3-E-PM11 Manual preview
PRIME DESIGN VRI3-E-PM11
Бренд: Safe Fleet Страницы: 12
Whispbar K934W Fitting Instructions Manual preview
K934W
Бренд: Whispbar Страницы: 15
BendPak Autostacker PL-6SR Installation And Operation Manual preview
Autostacker PL-6SR
Бренд: BendPak Страницы: 104
Connects2 adaptiv mini ADVM-BM1 Fitting & User Manual preview
adaptiv mini ADVM-BM1
Бренд: Connects2 Страницы: 4
VDO RUDDER ANGLE INDICATOR Installation Instructions Manual preview
RUDDER ANGLE INDICATOR
Бренд: VDO Страницы: 8
Chevrolet 1996 Cavalier Owner'S Manual preview
1996 Cavalier
Бренд: Chevrolet Страницы: 372
Mobileye C2-270 User Manual preview
C2-270
Бренд: Mobileye Страницы: 29
Ranger design 1525-PC Installation Manual preview
1525-PC
Бренд: Ranger design Страницы: 22
Smappee EVB-1332-BL-E Installation Manual preview
EVB-1332-BL-E
Бренд: Smappee Страницы: 28
Dodge 2004 JR41 Stratus Sedan Owner'S Manual preview
2004 JR41 Stratus Sedan
Бренд: Dodge Страницы: 273
Mazda 2014 CX-9 User Manual preview
2014 CX-9
Бренд: Mazda Страницы: 604
Buick Enclave Owner'S Manual preview
Enclave
Бренд: Buick Страницы: 394
TIS TISPLUS User Manual preview
TISPLUS
Бренд: TIS Страницы: 6
FALCON RIDGE KY-700-2018-DRW01 Instructions For Installation And Care preview
KY-700-2018-DRW01
Бренд: FALCON RIDGE Страницы: 7
Fiat FIORINO Owner'S Handbook Manual preview
FIORINO
Бренд: Fiat Страницы: 220
Toyota RAV4 2019 Owner'S Manual preview
RAV4 2019
Бренд: Toyota Страницы: 244
SSANGYONG Actyon 2008 Manual preview
Actyon 2008
Бренд: SSANGYONG Страницы: 81

Бренды по названию

Популярные бренды

Загрузить еще бренды