manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

DEPLOYED AIR BAG (INFLATOR) MODULE
DISPOSAL

WARNING:
Failure to follow proper air bag (inflator) module disposal
procedures can result in air bag deployment which may
cause personal injury. The undeployed air bag (inflator)
module must not be disposed of through normal refuse
channels.
The undeployed air bag (inflator) module contains sub-
stances that can cause severe illness or personal injury
if the sealed container is damaged during disposal.

Deployed air bag (inflator) module can be disposed of through nor-
mal refuse channels just like any other parts. For their disposal,
however, following points should be noted.

The air bag (inflator) module immediately after deployment is
very hot. Wait for 30 minutes to cool it off before handling it.

Never apply water, oil, etc. to deployed air bag (inflator) module
to cool it off and be careful so that water, oil etc. does not get on
the deployed air bag (inflator) module.

After the air bag (inflator) module has been deployed, the sur-
face of the air bag may contain a powdery residue. This powder
consists primarily of cornstarch (used to lubricate the bag as it
inflates) and byproducts of the chemical reaction. As with many
service procedures, you should wear gloves and safety glasses.

When disposing of the deployed air bag (inflator) module, be
sure to seal it in a vinyl bag.

When air bag (inflator) module have been deployed inside the
vehicle which is going to be scrapped, leave them as installed
to the vehicle.

Be sure to wash your hands with mild soap and water after han-
dling it.

10B-56

AIR BAG SYSTEM

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

Jeep Compass Owner'S Handbook Manual preview
Compass
Бренд: Jeep Страницы: 322
Jeep Compass Repair Manual preview
Compass
Бренд: Jeep Страницы: 341
Jeep Compass Operating Information Manual preview
Compass
Бренд: Jeep Страницы: 310
Jeep Compass Information Manual preview
Compass
Бренд: Jeep Страницы: 189
Jeep Compass Review preview
Compass
Бренд: Jeep Страницы: 26
Jeep Compass Overview preview
Compass
Бренд: Jeep Страницы: 21
Paxton Automotive Novi Owner'S Installation Manual preview
Novi
Бренд: Paxton Automotive Страницы: 85
Thule 1489 Instructions Manual preview
1489
Бренд: Thule Страницы: 8
Wagan 2227-1 User Manual preview
2227-1
Бренд: Wagan Страницы: 8
Thermo King T- series Driver Manual To Simple Operation preview
T- series
Бренд: Thermo King Страницы: 2
Masterack RM470057 Assembly Instructions preview
RM470057
Бренд: Masterack Страницы: 4
Over Armour Offroad KAW-SX-SDK01 Instructions For Installation And Care preview
KAW-SX-SDK01
Бренд: Over Armour Offroad Страницы: 5
Honda 2011 Civic Sedan Vehicle Instruction Card preview
2011 Civic Sedan
Бренд: Honda Страницы: 5
Suzuki 990E0-54P56-000 Installers And Users Instructions preview
990E0-54P56-000
Бренд: Suzuki Страницы: 12
Dometic Heki 2 Installation And Operating Manual preview
Heki 2
Бренд: Dometic Страницы: 158
Maserati Gransport Owner'S Manual preview
Gransport
Бренд: Maserati Страницы: 210
OnStar liveon Owner'S Manual preview
liveon
Бренд: OnStar Страницы: 22
Honda 08A06-361-210 Installation Instructions preview
08A06-361-210
Бренд: Honda Страницы: 4

Бренды по названию

Популярные бренды

Загрузить еще бренды