manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

4) Check O-ring for damage or deterioration. With O-ring groove

in rocker arm shaft exposed to transmission side once, install
O-ring to rocker arm shaft.

1. Rocker arm shaft
2. O-ring

5) Set rocker arm shaft so that its cut part becomes in parallel with

head cover mating surface.
Face rocker arm shaft pivot holding part (for intake rocker arm)
up.

Dimension “a” : 5mm (0.20 in.)

1. Parallel
2. Cut part
3. Cylinder block

6) Install rocker arm shaft bolts and tighten them to specified

torque.

Tightening Torque
(a): 11 N

.

m (1.1 kg-m, 8.0 lb-ft)

7) Fill small amount of engine oil into arm pivot holding part of rock-

er arm shaft. Install rocker arm (intake side) with clips to rocker
arm shaft.

1. Rocker arm
2. Clip
3. Pivot holding part

8) Apply engine oil to cams and journals on camshaft and put cam-

shaft on cylinder head. Install camshaft housing to camshaft
and cylinder head.

Apply engine oil to sliding surface of each housing against
camshaft journal.

Apply sealant to mating surface of No.6 housing which will
mate with cylinder head.

“A” Sealant: 99000-31110

1. Timing belt side
2. Flywheel side

6A-32

ENGINE MECHANICAL

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

Camcar 2155 Fitting Instructions preview
2155
Бренд: Camcar Страницы: 2
Mazdaspeed QSEA 51 96Z Installation And User Instructions Manual preview
QSEA 51 96Z
Бренд: Mazdaspeed Страницы: 8
Ford FIESTA ST 2019 Supplement Manual preview
FIESTA ST 2019
Бренд: Ford Страницы: 37
Whispbar K604W Fitting Instructions Manual preview
K604W
Бренд: Whispbar Страницы: 15
Tachosys digidl Installation Manual preview
digidl
Бренд: Tachosys Страницы: 28
Lantronix FOX3 Series Hardware Manual preview
FOX3 Series
Бренд: Lantronix Страницы: 51
Pontiac 2006 Relay Getting To Know Manual preview
2006 Relay
Бренд: Pontiac Страницы: 20
Horn Tools HJIMRR02FIT Mounting Instructions preview
HJIMRR02FIT
Бренд: Horn Tools Страницы: 12
PUTCO 1951 Series Instruction Manual preview
1951 Series
Бренд: PUTCO Страницы: 3
Curt Group 60638 Installation Manual preview
60638
Бренд: Curt Group Страницы: 3
Juna JRDAB-03 Installation Manual preview
JRDAB-03
Бренд: Juna Страницы: 10
MMD 41240 Quick Manual preview
41240
Бренд: MMD Страницы: 3
Volvo Ski box Installation Instructions Manual preview
Ski box
Бренд: Volvo Страницы: 7
Yenkee YAC 450 User Manual preview
YAC 450
Бренд: Yenkee Страницы: 22
Opel 2011 Astra J Owner'S Manual preview
2011 Astra J
Бренд: Opel Страницы: 242
Kuda 050130 Installation Instruction preview
050130
Бренд: Kuda Страницы: 4
Brodit 841488 Quick Start Manual preview
841488
Бренд: Brodit Страницы: 2
ACV 381178-12 Installation Manual preview
381178-12
Бренд: ACV Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды