manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

COMBINATION METER

REMOVAL

1) Disconnect negative cable at battery.
2) Loosen steering column mounting screws and nuts. (Refer to

“STEERING WHEEL AND COLUMN” section.)

3) Remove meter cluster panel. Make sure to disconnect all cou-

plers of switches and wires of cigarette lighter on meter cluster.

4) Disconnect couplers from combination meter.

Remove combination meter.

INSTALLATION

Reverse removal procedure for installation.

1. Combination meter
2. Cluster panel

LH steering vehicle shown

INSPECTION

Check printed plate visually for scratch, crack and discoloration. If
any of such faulty conditions is found, replace the printed plate.

1. Combination meter

VEHICLE SPEED SENSOR

Refer to VEHICLE SPEED SENSOR in SECTION 6E of this manu-
al.

8-22

BODY ELECTRICAL SYSTEM

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

cam HS Series Operating Manual preview
HS Series
Бренд: cam Страницы: 28
Jeep GRAND CHEROKEE 2023 Information Manual preview
GRAND CHEROKEE 2023
Бренд: Jeep Страницы: 108
UMBRA RIMORCHI 39030 Installation Instructions Manual preview
39030
Бренд: UMBRA RIMORCHI Страницы: 18
AA Products RB0007 Instruction Manual preview
RB0007
Бренд: AA Products Страницы: 6
Metra Electronics 99-7477 Installation Instructions preview
99-7477
Бренд: Metra Electronics Страницы: 2
Tellur BASIC TLL171231 User Manual preview
BASIC TLL171231
Бренд: Tellur Страницы: 5
Yakima K614 Manual preview
K614
Бренд: Yakima Страницы: 12
FALCON RIDGE CF-1000-WD05 Instructions For Installation And Care preview
CF-1000-WD05
Бренд: FALCON RIDGE Страницы: 6
Bestop Bikini Installation Instructions preview
Bikini
Бренд: Bestop Страницы: 5
PowerMadd Tri-mount Installation Instructions preview
Tri-mount
Бренд: PowerMadd Страницы: 3
Ratio Power box Manual preview
Power box
Бренд: Ratio Страницы: 12
Horn Tools PHRRF002 Mounting Instructions preview
PHRRF002
Бренд: Horn Tools Страницы: 8
J. Strong JST506BT Installation Instructions preview
JST506BT
Бренд: J. Strong Страницы: 2
Dometic LMC Eriba Nova Service Manual preview
LMC Eriba Nova
Бренд: Dometic Страницы: 24
Ford F-250 Super Duty 2022 Owner'S Manual preview
F-250 Super Duty 2022
Бренд: Ford Страницы: 740
Phonocar VM 320 Instruction Manual preview
VM 320
Бренд: Phonocar Страницы: 28
Summit Racing SUM-G1083 Assembly & Use Instructions preview
SUM-G1083
Бренд: Summit Racing Страницы: 11
Yakima FreshSesh PowderHound Manual preview
FreshSesh PowderHound
Бренд: Yakima Страницы: 18

Бренды по названию

Популярные бренды

Загрузить еще бренды