manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

5E-22

ANTILOCK BRAKE SYSTEM (ABS) (OPTIONAL)

INSPECTION

STEP

ACTION

YES

NO

1

1) Disconnect applicable sensor connector with 

ignition switch OFF.

2) Measure resistance between sensor terminals.

Resistance of wheel speed sensor: 1.2 – 1.6 k

(at 20

C, 68

F)

3) Measure resistance between each terminal and body

ground.

Insulation resistance: 1M

 or higher

Were measured resistance values in step 2) and 3) as

specified? (See Fig. 1)

Go to step 2.

Replace sensor.

2

1) Ignition switch OFF.

2) Disconnect connector from ABS hydraulic unit / control

module assembly. (See Fig. 2)

3) Check for proper connection to ABS hydraulic

unit / control module assembly at each sensor termi-

nal.

4) If OK then, turn ignition switch ON and measure 

voltage between sensor positive terminal of module

connector and body ground.

Is it 0V?

Go to step 3.

Sensor positive 

circuit shorted to

power.

3

1) Ignition switch OFF.

2) Connect connector to sensor.

3) Measure resistance between sensor terminals at 

module connector.

4) Measure resistance between sensor positive terminal

and negative terminal of module connector, between

positive terminal and body ground.

Are measured resistance values within each specified

range described in above step 1)?

Go to step 4.

Circuit open or

shorted to ground.

4

1) Remove wheel speed sensor.

2) Check sensor for damage or foreign material being

attached.

Is it in good condition? (See Fig. 3)

Go to step 5.

Clean or replace

sensor.

5

Check visually through wheel speed sensor installation

hole for following.

Rotor serration (teeth) neither missing or damaged.

No foreign material being attached.

Rotor not being eccentric.

Wheel bearing free from excessive play.

Are they in good condition? (See Fig. 4)

Go to step 6.

Clean, repair or 

replace.

6

1) Install sensor to knuckle or axle housing.

2) Tighten sensor bolt to specified torque and check that

there is not any clearance between sensor and

knuckle or axle housing. (See Fig. 5)

Replace sensor if any.

Referring to item OUTPUT VOLTAGE INSPECTION of

FRONT WHEEL SPEED SENSOR, check output voltage

or waveform of sensor. Is proper output voltage or 

waveform obtained?

Substitute a known-

good ABS hydraulic

unit /control module 

assembly and recheck.

Replace sensor

and recheck.

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

U.S. General 97845 Set Up And Operating Instructions preview
97845
Бренд: U.S. General Страницы: 5
Back View RV-250 User Manual preview
RV-250
Бренд: Back View Страницы: 168
Mitsubishi 1998 FTO Technical Information Manual preview
1998 FTO
Бренд: Mitsubishi Страницы: 160
Cadillac 2004 CTS Owner'S Manual preview
2004 CTS
Бренд: Cadillac Страницы: 442
Actia TGU-R ACCESS User Manual preview
TGU-R ACCESS
Бренд: Actia Страницы: 37
GMC Envoy XUV 2004 Getting To Know Manual preview
Envoy XUV 2004
Бренд: GMC Страницы: 20
BMW E46/2 Coupe Manual preview
E46/2 Coupe
Бренд: BMW Страницы: 55
Whispbar K496W Fitting Instructions Manual preview
K496W
Бренд: Whispbar Страницы: 15
Whispbar K607W Fitting Instructions Manual preview
K607W
Бренд: Whispbar Страницы: 14
WABCO OnSide MM16167 Maintenance Manual preview
OnSide MM16167
Бренд: WABCO Страницы: 52
Park-Daddy PD50AA Installation Manual preview
PD50AA
Бренд: Park-Daddy Страницы: 22
Toyota Sienna 2021 Manual preview
Sienna 2021
Бренд: Toyota Страницы: 600
AIS MAZMOD2 Manual preview
MAZMOD2
Бренд: AIS Страницы: 2
Subaru Legacy 2011 Quick Reference Manual preview
Legacy 2011
Бренд: Subaru Страницы: 19
Acura 08L07-TA1-203 Installation Instructions Manual preview
08L07-TA1-203
Бренд: Acura Страницы: 6
Prorack K623 Fitting Instructions Manual preview
K623
Бренд: Prorack Страницы: 15
Mazda 0000-8L-G03A Installation Instructions preview
0000-8L-G03A
Бренд: Mazda Страницы: 3
Honda 08B15-SDN-100 Installation Instructions Manual preview
08B15-SDN-100
Бренд: Honda Страницы: 22

Бренды по названию

Популярные бренды

Загрузить еще бренды