manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

3) Remove back door balancer (first at its door-side and next at its

body-side).

4) Remove door hinge bolts and door.

WARNING:
Handling of Back Door Balancer (Damper)

Do not disassemble balancer because its cylinder
is filled with gas.

The gas itself is harmless but it may issue out of the
hole together with chips generated by the drill.
Therefore, be sure to wear goggle.

When discarding removed back door balancer
(damper), use a 2 to 3 mm (0.08 to 0.12 in.) drill to
make a hole as shown.

Handle balancer carefully. Do not scar or scratch
exposed surface of its piston rod, and never allow
any paint or oil to stick to its surface.

Do not turn piston rod with balancer fully extended.

INSTALLATION

Reverse removal procedure to install back door by note the follow-
ing procedure.

NOTE:
When replacing back door, coat replacement door inside with
wax for proper anticorrosive treatment. Refer to RUST PROOF
TREATMENT AREA in this section.

Install back door with applying rust proof sealant to hinge fitting
surface.

Secure wiring harness and connect couplers.

Install door latch striker with its arrow mark indicating front side
of vehicle.

Adjust the door latch striker so that striker center aligns with the
center of grove in door latch base.
To adjust door latch and striker each other, insert proper number
of shims below the bottom of striker.

For correct installation, see PANEL CLEARANCE and adjust
door hinge properly.

1. Door latch
2. Shim
3. Door latch striker
4. Forward

BODY SERVICE

9-15

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

Toyota 2012 Rav4 Owner'S Manual preview
2012 Rav4
Бренд: Toyota Страницы: 529
Porsche Carrera GT Manual preview
Carrera GT
Бренд: Porsche Страницы: 192
Metra Electronics 95-6556 Installation Instructions preview
95-6556
Бренд: Metra Electronics Страницы: 4
Rostra REARSIGHT OnStar 250-8822 Installation Instructions preview
REARSIGHT OnStar 250-8822
Бренд: Rostra Страницы: 2
Phonocar VM338 Mounting Instructions preview
VM338
Бренд: Phonocar Страницы: 6
WABCO TP19108 Installation Manual preview
TP19108
Бренд: WABCO Страницы: 32
Thule CIRCUIT 526XT Manual preview
CIRCUIT 526XT
Бренд: Thule Страницы: 12
Mercedes-Benz R 350 2012 Operator'S Manual preview
R 350 2012
Бренд: Mercedes-Benz Страницы: 368
Road Ranger H392 Installation Manual preview
H392
Бренд: Road Ranger Страницы: 22
Daesung HM-TX-315 User Manual preview
HM-TX-315
Бренд: Daesung Страницы: 9
Pontiac 2010 Vibe Owner'S Manual preview
2010 Vibe
Бренд: Pontiac Страницы: 318
C-KO RS-4-18-R-I Fitting Instructions preview
RS-4-18-R-I
Бренд: C-KO Страницы: 4
Safe Fleet Prime Design VBI-FT31B Assembly Instructions Manual preview
Prime Design VBI-FT31B
Бренд: Safe Fleet Страницы: 12
Volvo 30661683 Installation Instructions, Accessories preview
30661683
Бренд: Volvo Страницы: 18
Ford 2003 Mustang Workshop Manual preview
2003 Mustang
Бренд: Ford Страницы: 4378
Toyota 2013 Prius c Owner'S Manual preview
2013 Prius c
Бренд: Toyota Страницы: 549
Seat Toledo 2019 Owner'S Manual preview
Toledo 2019
Бренд: Seat Страницы: 300
CITROEN CX 2000 Repair Manual preview
CX 2000
Бренд: CITROEN Страницы: 394

Бренды по названию

Популярные бренды

Загрузить еще бренды