manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

7) Remove reservoir tank and remove cap from reservoir tank

and pour out any fluid, scrub and clean inside of tank with soap
and water.
Flush it well with clean water and drain. Reinstall tank.

8) Add 50/50 mixture of good quality ethylene glycol antifreeze

and water to radiator and tank.
Bleed air from cooling system by disconnecting heater breath-
er hose and loosening thermostat cap bleeder bolt, and add
coolant to radiator until coolant comes out from thermostat cap
bleeder hole. Then tighten thermostat cap bleeder bolt.

Tightening Torque
(a): 3.0 N·m (0.3 kg-m, 2.2 Ib-ft)

9) Fill radiator to the base of radiator filler neck and reservoir tank

to “FULL” level mark. Reinstall reservoir tank cap.

10) Connect heater breather hose.
11) Run engine with radiator cap removed, until radiator upper

hose is hot. Add coolant to radiator until level reaches the bot-
tom of filler neck.

12) Stop engine and install radiator cap, making sure that the ear

of cap lines is parallel to radiator. Add coolant to reservoir
when engine cold.

13) Repeat step 8) to 12) accordingly when air is still in cooling sys-

tem.

1. Thermostat cap

bleeder bolt

2. Thermostat cap

3. Heater breather hose
4. Vehicle jack

WATER PUMP BELT TENSION

1) Inspect belt for cracks, cuts, deformation, wear and cleanliness.

If it is necessary to replace belt, refer to “Generator (Water
Pump) Belt” in CHARGING SYSTEM section for procedure.

WARNING:

Disconnect negative cable at battery before checking
and adjusting belt tension.

See “WARNING” described in “COOLING SYSTEM
SERVICE”.

2) Check belt for tension. Belt is in proper tension when it deflects

6 to 8 mm (0.24 – 0.31 in.) under thumb pressure (about 10 kg
or 22 Ib.).

Belt tension “a”: 6 – 8mm (0.24 – 0.31 in.) as deflection

NOTE:
When replacing belt with a new one, adjust belt tension to
5 – 7 mm (0.20 – 0.28 in.).

3) If belt is too tight or too loose, adjust it to proper tension by dis-

placing generator position (Refer to Section 6H).

4) Tighten belt adjusting bolt and generator pivot bolts.
5) Connect negative cable at battery terminal.

1. 10kg (22 lbs)
2. Adjusting bolt

ENGINE COOLING

6B-7

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

UMBRA RIMORCHI 39030 Installation Instructions Manual preview
39030
Бренд: UMBRA RIMORCHI Страницы: 18
Toyota 2011 Corolla LE Brochure preview
2011 Corolla LE
Бренд: Toyota Страницы: 19
DAVIS 8126GD User Manual preview
8126GD
Бренд: DAVIS Страницы: 32
FORM FIT 1303 Installation Instructions preview
1303
Бренд: FORM FIT Страницы: 2
Haibang HA998 Series Installation Instructions Manual preview
HA998 Series
Бренд: Haibang Страницы: 6
Alfa Romeo FIX&GO automatic Manual preview
FIX&GO automatic
Бренд: Alfa Romeo Страницы: 40
Maserati Quattroporte Automatic Owner'S Manual preview
Quattroporte Automatic
Бренд: Maserati Страницы: 272
Connects2 adaptiv mini ADVM-BM1 Fitting & User Manual preview
adaptiv mini ADVM-BM1
Бренд: Connects2 Страницы: 4
Q Mobility Group Q Access Alpha GSE 2023 Installation Manual preview
Q Access Alpha GSE 2023
Бренд: Q Mobility Group Страницы: 9
Xhorse VVDI User Manual preview
VVDI
Бренд: Xhorse Страницы: 48
Hama 00 123530 Operating Instructions preview
00 123530
Бренд: Hama Страницы: 4
Volvo 1992 850 Service And Repair Manual preview
1992 850
Бренд: Volvo Страницы: 230
BMW 323Ci Manual preview
323Ci
Бренд: BMW Страницы: 189
GMC TopKick 2007 Owner'S Manual preview
TopKick 2007
Бренд: GMC Страницы: 430
Lexus HS 250h Vehicle Dismantling Manual preview
HS 250h
Бренд: Lexus Страницы: 34
Toyota 86 2020 Quick Reference Manual preview
86 2020
Бренд: Toyota Страницы: 32
Demco TP20047 Assembly Operation Replacement Parts preview
TP20047
Бренд: Demco Страницы: 4
v.link VL2-MBN2 Manual preview
VL2-MBN2
Бренд: v.link Страницы: 12

Бренды по названию

Популярные бренды

Загрузить еще бренды