manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

Viscosity chart
SAE

80W-90

75W-85, 75W-90

°

C

°

F

–30

–22

–20

–4

–10

14

0

32

10

50

20

68

30

86

40

104

Temperature

7A1-4

MANUAL TRANSMISSION (4WD)

ON-VEHICLE SERVICE

MAINTENANCE SERVICE

OIL CHANGE

The transfer oil is used as manual transmission oil as well.
1) Before changing or inspecting oil, be sure to stop engine and lift

vehicle horizontally.

2) With vehicle lifted up, check oil level and leakage. If leakage ex-

ists, correct or repair it.

3) Remove 2 drain plugs (1) drain old oil. Then torque drain plug

as specified below after applying sealant to their thread.

“A”: Sealant 99000-31110

Tightening Torque
(a): 23 N

.

m (2.3 kg-m, 17.0 lb-ft)

4) Fill new specified oil as shown below by specified amount

(roughly up to level hole).

NOTE:

D

It is highly recommended to use SAE 75W-90 gear oil.

D

Whenever vehicle is hoisted for any service work other
than oil change, also be sure to check for oil leakage.

D

If water or rust is mixed in drained oil, be sure to check
breather of transmission.

Gear Oil Specification

Oil grade: API GL-4
Viscosity: SAE 75W-85, 75W-90 or 80W-90

Oil Capacity:

AXC externally mounted type transmission:
3.5 liters (7.40 / 6.16 US / lmp. pt)
AXC built-in type transmission:
3.7 liters (7.90 / 6.51 US / lmp. pt)

5) Torque level / filler plug (2) in the same manner as drain plug.

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

KC HiLiTES C Series Wiring Diagram preview
C Series
Бренд: KC HiLiTES Страницы: 4
Ranger design 5044 Installation Manual preview
5044
Бренд: Ranger design Страницы: 6
Lancia Y Owner'S Handbook Manual preview
Y
Бренд: Lancia Страницы: 191
Yakima K343 Manual preview
K343
Бренд: Yakima Страницы: 11
Laser 4832 Manual preview
4832
Бренд: Laser Страницы: 8
AccuAir AA-4397 Installation Manual preview
AA-4397
Бренд: AccuAir Страницы: 40
Peak PKC0RG Owner'S Manual preview
PKC0RG
Бренд: Peak Страницы: 10
Cadillac ESCALADE FAMILY - SPECIFICATIONS 2011 Specifications preview
ESCALADE FAMILY - SPECIFICATIONS 2011
Бренд: Cadillac Страницы: 1
APS Auto Parts Specialist iBoard IB-ZK406 Installation Instructions preview
iBoard IB-ZK406
Бренд: APS Auto Parts Specialist Страницы: 3
Sumitomo Dunlop L.D02.C.M Installation Manual preview
Dunlop L.D02.C.M
Бренд: Sumitomo Страницы: 22
Axxess AXRC-CH1 Installation Instructions Manual preview
AXRC-CH1
Бренд: Axxess Страницы: 8
Dodge Charger 1973 Body Service Manual preview
Charger 1973
Бренд: Dodge Страницы: 276
Caltrend LY115 Installation Instructions preview
LY115
Бренд: Caltrend Страницы: 3
Navman T1 F20 User Manual preview
T1 F20
Бренд: Navman Страницы: 10
Macrom EF-AR1-5561 Manual preview
EF-AR1-5561
Бренд: Macrom Страницы: 10
Waeco MagicSpeed MS900 Installation Manual preview
MagicSpeed MS900
Бренд: Waeco Страницы: 120
Lock'er Down 2011 X Instructions preview
2011 X
Бренд: Lock'er Down Страницы: 2
Skoda 2015 Superb Owner'S Manual preview
2015 Superb
Бренд: Skoda Страницы: 276

Бренды по названию

Популярные бренды

Загрузить еще бренды