manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

Front differential

Rear differential

1. Drain plug
2. Oil filler / level plug

0B1-18

MAINTENANCE AND LUBRICATION (4WD)

Change

Change transmission oil with new specified oil. Refer to MAINTE-
NANCE SERVICE in SECTION 7A1.

CAUTION:
Specified gear oil must be used for differential.

ITEM 6-10

Differential Oil

Inspection

1) Check differential for evidence of oil leakage.

Repair leaky point if any.

2) Make sure that vehicle is placed level for oil level check.
3) Remove level plug of differential and check oil level.

Oil level can be checked roughly by means of level plug hole.
That is, if oil flows out of level plug hole or if oil level is found up
to hole when level plug is removed, oil is properly filled.
If oil is found insufficient, pour specified amount of specified oil.

CAUTION:
Specified gear oil must be used for differential.

4) Tighten level plug to specified torque.

Refer to OIL CHANGE in SECTION 7E and SECTION 7F.

Change

Change differential oil with new specified oil. Refer to OIL CHANGE
in SECTION 7F respectively.

ITEM 6-11

Steering System

Inspection

1) Check steering wheel for play and rattle, holding vehicle in

straight forward condition on the ground.

Steering wheel play 

“

a

”

: 0 

–

 30 mm (0 

–

 1.2 in.)

2) Check that steering wheel can be turned fully to the right and left.

Repair or replace defective parts, if any.

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

GOgroove SMARTmini AUX Operating Manual preview
SMARTmini AUX
Бренд: GOgroove Страницы: 9
Saleen 10-8002-C11998B Installation Manual preview
10-8002-C11998B
Бренд: Saleen Страницы: 12
Buick 2013 Buick Verano Manual preview
2013 Buick Verano
Бренд: Buick Страницы: 5
Metra Electronics 99-3103 Installation Instructions preview
99-3103
Бренд: Metra Electronics Страницы: 2
Subaru 2005 Baja Owner'S Manual preview
2005 Baja
Бренд: Subaru Страницы: 34
FAAFTECH FT-VF-HND2 Installation Manual preview
FT-VF-HND2
Бренд: FAAFTECH Страницы: 8
AutoMaxi AXIS XXL Instructions preview
AXIS XXL
Бренд: AutoMaxi Страницы: 2
Quadratec 12226.3011 Installation Manual preview
12226.3011
Бренд: Quadratec Страницы: 8
Toyota CAMRY HV Manual preview
CAMRY HV
Бренд: Toyota Страницы: 636
Ranger design 1525-FTR Installation Manual preview
1525-FTR
Бренд: Ranger design Страницы: 24
Aries 205039 Installation Manual preview
205039
Бренд: Aries Страницы: 5
Mercedes-Benz MY17 c-class Operator'S Manual preview
MY17 c-class
Бренд: Mercedes-Benz Страницы: 354
Subaru 1994 Impreza Supplemental Service Manual preview
1994 Impreza
Бренд: Subaru Страницы: 540
Curtis 1POLXP1000RP Installation & Owner'S Manual preview
1POLXP1000RP
Бренд: Curtis Страницы: 6
Discount Car Stereo A2DIY-MBR Quick Start Bluetooth Installation Manual preview
A2DIY-MBR
Бренд: Discount Car Stereo Страницы: 8
Ford TRANSIT CUSTOM Quick Reference Manual preview
TRANSIT CUSTOM
Бренд: Ford Страницы: 15
Honda 08L04-SZA-100 Installation Instructions preview
08L04-SZA-100
Бренд: Honda Страницы: 3
Belkin TuneBase F8Z442 User Manual preview
TuneBase F8Z442
Бренд: Belkin Страницы: 162

Бренды по названию

Популярные бренды

Загрузить еще бренды