manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

BRAKES

5-9

LSPV (Load Sensing Proportioning Valve) ASSEMBLY (If equipped)

As shown below, LSPV is included within the brake circuit which connects the master cylinder and the rear wheel
brake. It controls the hydraulic pressure applied to the rear wheel brake according to the loaded state of the vehicle
(or weight of the load), whereby preventing the rear wheels from getting locked prematurely. Also, it releases the
above described control over the hydraulic pressure applied to the rear wheel brake, should any failure occur in
the hydraulic circuit of the front wheel brake so that the hydraulic pressure produced in the master cylinder is ap-
plied to the rear wheel brake directly to operate it.

CAUTION:
Never disassemble LSPV. Disassembly will spoil its original function. If faulty condition is found, re-
place it with new one.

1. LSPV spring
2. LSPV assembly
3. From master cylinder (Secondary)
4. To rear wheel brakes (Right and Left)
5. From master cylinder (Primary)
6. Loaded
7. Empty

CONSTRUCTION

The LSPV components are grounded into 3 sections as follows.
“A”:

Sensor section
The main parts in this section are a lever and a spring which senses variation in the vehicle height as affected
by the loaded condition and convert it into the load.

“B”:

Hydraulic pressure control section
Included in this section are a plunger and valve mechanism to execute proportional control.

“C”:

Fail-safe section
The main part in this section is a chamber which draws in the hydraulic pressure from the front wheel brake
system and a fail-safe piston which releases the valve mechanism in the control section connected to the
rear wheel brake, should any failure occur in the front wheel brake system.

1. Plunger
2. LSPV lever
3. Load sensing spring
4. From master cylinder

primary chamber
(Rear wheel brake)

5. To rear wheel brake
6. From master cylinder

secondary chamber
(Front wheel brake)

7. Bleeder plug
8. Collar

Never adjust

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

Oldsmobile 2004 Alero Owner'S Manual preview
2004 Alero
Бренд: Oldsmobile Страницы: 360
Porsche 911 GT3R 2010 Technical Manual preview
911 GT3R 2010
Бренд: Porsche Страницы: 144
Porsche 911 GT3 - Brochure preview
911 GT3 -
Бренд: Porsche Страницы: 51
Whispbar K710W Fitting Instructions For Basic Carrier preview
K710W
Бренд: Whispbar Страницы: 14
Honda 2004 S2000 Owner'S Manual preview
2004 S2000
Бренд: Honda Страницы: 208
Oldsmobile 2004 Alero Quick Manual preview
2004 Alero
Бренд: Oldsmobile Страницы: 2
Ecco 5545A Installation And Operating Instructions Manual preview
5545A
Бренд: Ecco Страницы: 12
Skoda Superb 2006 Owner'S Manual preview
Superb 2006
Бренд: Skoda Страницы: 281
Flash Cover MN019 Instructions preview
MN019
Бренд: Flash Cover Страницы: 2
Porsche WTY 2010 Warranty & Maintenance Manual preview
WTY 2010
Бренд: Porsche Страницы: 98
Thule RaceWay 991 Instructions Manual preview
RaceWay 991
Бренд: Thule Страницы: 12
Mazda 2010 MX-5 Miata Specification preview
2010 MX-5 Miata
Бренд: Mazda Страницы: 8
Toyota RAV-4 2015 Series Owner'S Manual Supplement preview
RAV-4 2015 Series
Бренд: Toyota Страницы: 50
Autoplugin RCP-B1 Installation Manual preview
RCP-B1
Бренд: Autoplugin Страницы: 8
Magneti Marelli AC911 Installation Instruction preview
AC911
Бренд: Magneti Marelli Страницы: 3
Goobay KFZ 112 Quick Start Manual preview
KFZ 112
Бренд: Goobay Страницы: 2
CITROEN 2 CV4 Owner'S Manual preview
2 CV4
Бренд: CITROEN Страницы: 86
Whelen Engineering Company 12H4S140 Installation Manual preview
12H4S140
Бренд: Whelen Engineering Company Страницы: 4

Бренды по названию

Популярные бренды

Загрузить еще бренды