manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

6E-44

ENGINE AND EMISSION CONTROL SYSTEM

TABLE B-4 IDLE AIR CONTROL SYSTEM CIRCUIT CHECK

SYSTEM AND WIRING DIAGRAM

1. Throttle body
2. From air cleaner
3. To intake manifold
4. IAC valve
5. IAC valve connector
6. TP sensor
7. TP sensor connector
8. ECM connector (A)
9. ECM connector (B)

10. ECM
11. Power supply from main relay

SYSTEM DESCRIPTION

ECM transmits duty signal to IC in IAC valve. Then, the IC controls current of IAC valve coils.

INSPECTION

STEP

ACTION

YES

NO

1

Did you perform “ENGINE DIAGNOSTIC FLOW

TABLE” in Section 6?

Go to Step 2.

Go to “ENGINE DIAG-

NOSTIC FLOW TABLE”.

2

1) Perform “IAC Valve Inspection” in this section.
Is IAC valve in good condition?

Go to Step 3.

Go to Step 6.

3

1) With ignition switch OFF position, install SUZU-

KI scan tool.

2) Turn ignition switch ON position, leaving engine

OFF.

3) Monitor closed throttle position (“CLOSE

THROT POS”) parameter on SUZUKI scan
tool.

Does scan tool indicate “ON” when throttle valve is

fully closed and then “OFF” when throttle valve is

opened?

Faulty EVAP canister

purge valve.

Faulty PCV valve.

Faulty EGR system.

Faulty A/C signal.

Faulty engine accessory.

Go to Step 4.

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

cam HS Series Operating Manual preview
HS Series
Бренд: cam Страницы: 28
VEAP SHIELD UNITED FT Series Mounting Instruction preview
FT Series
Бренд: VEAP SHIELD UNITED Страницы: 3
Jeda Wireless Pad Manual preview
Wireless Pad
Бренд: Jeda Страницы: 8
Jeep 2009 Wrangler Owner'S Manual preview
2009 Wrangler
Бренд: Jeep Страницы: 496
Jeep GRAND CHEROKEE 2023 Information Manual preview
GRAND CHEROKEE 2023
Бренд: Jeep Страницы: 108
Kargo Master 80070 Assembly Lnstructions preview
80070
Бренд: Kargo Master Страницы: 13
Kargo Master 4A96L Installation Manual preview
4A96L
Бренд: Kargo Master Страницы: 21
Kargo Master 40201 Installation Manual preview
40201
Бренд: Kargo Master Страницы: 4
Tesla V2 SUPERCHARGER First Responder'S Manual preview
V2 SUPERCHARGER
Бренд: Tesla Страницы: 9
Code 3 21 COVERT Series Installation And Operation Instructions Manual preview
21 COVERT Series
Бренд: Code 3 Страницы: 16
iArmor IA-N179 Manual preview
IA-N179
Бренд: iArmor Страницы: 6
Metra Electronics 70-5511 Installation Instructions preview
70-5511
Бренд: Metra Electronics Страницы: 2
Neuspeed 25.02.22.2 Installation Instructions preview
25.02.22.2
Бренд: Neuspeed Страницы: 2
Porsche 911 GT3 - Brochure preview
911 GT3 -
Бренд: Porsche Страницы: 51
Whispbar K710W Fitting Instructions For Basic Carrier preview
K710W
Бренд: Whispbar Страницы: 14
Kia Sportage 2018 Features & Functions Manual preview
Sportage 2018
Бренд: Kia Страницы: 54
Safe Fleet PRIME DESIGN VRR-NV200 Manual preview
PRIME DESIGN VRR-NV200
Бренд: Safe Fleet Страницы: 12
Yakima Landing Pad 24 Quick Start Manual preview
Landing Pad 24
Бренд: Yakima Страницы: 11

Бренды по названию

Популярные бренды

Загрузить еще бренды