manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

6E-42

ENGINE AND EMISSION CONTROL SYSTEM

TABLE B-3 FUEL PRESSURE CHECK

SYSTEM DIAGRAM

1. Fuel pump
2. Fuel filter
3. Fuel feed line
4. Fuel pressure regulator
5. Vacuum passage for fuel pressure regulator
6. Fuel return line

SYSTEM DESCRIPTION

Fuel pressure regulator keeps the fuel pressure applied to injector 290kPa higher than that in intake manifold at
all times.

INSPECTION

NOTE:
Before using following table, check to make sure that battery voltage is higher than 11V. If battery voltage
is low, pressure becomes lower than specification even if fuel pump and line are in good condition.

STEP

ACTION

YES

NO

1

Did you perform “ENGINE DIAGNOSTIC FLOW

TABLE” in Section 6?

Go to Step 2.

Go to “ENGINE DIAG-

NOSTIC FLOW TABLE”.

2

1) Install fuel pressure gauge. Refer to “Fuel Pres-

sure Inspection” in this section.

2) Turn ignition switch ON position, leaving engine

OFF. After 3 seconds turn ignition switch OFF
position. Repeat this 3 or 4 times and observe
fuel pressure with fuel pump running.

Is fuel pressure indicated within 270 – 310 kPa 
(2.7 – 3.1 kg / cm

2

, 38.4 – 44.0 psi)?

Go to Step 3.

Go to Step 6.

3

1) Turn ignition switch OFF position.
2) Observe fuel pressure gauge for one minute

after fuel pump stops.

Does fuel pressure hold at or above 200 kPa 

(2.0

kg / cm

2

, 28.4 psi)?

Go to Step 4.

Fuel leaks from injector,

fuel pressure regulator

or fuel pump.

4

1) Start engine to normal operating temperature.
2) Keep it running at specified idle speed.
Is fuel pressure indicated within 210 – 260 kPa 
(2.1 – 2.6 kg / cm

2

, 29.8 – 37.0 psi)?

Go to Step 5.

Faulty vacuum passage

from intake manifold to

fuel pressure regulator.

Faulty fuel pressure reg-

ulator.

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

AAMP of America iSimple Operation Manual preview
iSimple
Бренд: AAMP of America Страницы: 6
Carax HUD CRX-3001 Quick Start Manual preview
HUD CRX-3001
Бренд: Carax Страницы: 2
Globalsat MR-350P Installation Manual preview
MR-350P
Бренд: Globalsat Страницы: 2
Mercedes-Benz 2016 SLK Operator'S Manual preview
2016 SLK
Бренд: Mercedes-Benz Страницы: 358
Metra Electronics 99-7477 Installation Instructions preview
99-7477
Бренд: Metra Electronics Страницы: 2
Xhorse VVDI User Manual preview
VVDI
Бренд: Xhorse Страницы: 48
Tellur BASIC TLL171231 User Manual preview
BASIC TLL171231
Бренд: Tellur Страницы: 5
EUFAB 11512 Manual preview
11512
Бренд: EUFAB Страницы: 4
GMC 2008 Savana Van Owner'S Manual preview
2008 Savana Van
Бренд: GMC Страницы: 402
Kolpin 1466 Product Instructions preview
1466
Бренд: Kolpin Страницы: 6
MBW i Wallbox Plus Owner'S Manual preview
i Wallbox Plus
Бренд: MBW Страницы: 40
JBA 1674S Installation Instructions preview
1674S
Бренд: JBA Страницы: 5
Valeo 632201 Instruction Manual preview
632201
Бренд: Valeo Страницы: 76
Mitsubishi MIRAGE Service Manual preview
MIRAGE
Бренд: Mitsubishi Страницы: 300
RAM PROMASTER 2018 User Manual preview
PROMASTER 2018
Бренд: RAM Страницы: 196
Masterack 022553KP Assembly/Installation Instructions preview
022553KP
Бренд: Masterack Страницы: 15
Metra Electronics GMRC-02 Installation Instructions preview
GMRC-02
Бренд: Metra Electronics Страницы: 2
Crux Sightline VIMCF-93C Quick Start Manual preview
Sightline VIMCF-93C
Бренд: Crux Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды