manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

INSTALLATION

Reverse removal procedure noting the following.

Clean mating surfaces of IAT sensor and air cleaner case.

Connect IAT sensor connector (1) securely.

1. IAT sensor
2. Air cleaner case

ENGINE COOLANT TEMPERATURE SENSOR
(ECT SENSOR)

REMOVAL

1) Disconnect battery negative cable at battery.
2) Drain coolant referring to Section 6B.

3) Remove generator referring to Section 6H.
4) Disconnect connector from ECT sensor.
5) Remove ECT sensor (1) from intake manifold.

WARNING:
To help avoid danger of being burned, do not remove
radiator cap while engine and radiator are still hot.
Scalding fluid and steam can be blown out under pres-
sure if cap is taken off too soon.

INSPECTION

Immerse temperature sensing part of ECT sensor (1) in water (or
ice) and measure resistance between terminals while heating wa-
ter gradually.
If measured resistance doesn’t show such characteristic as
shown, replace ECT sensor (1).

TEMPERATURE

RESIST

ANCE

ENGINE AND EMISSION CONTROL SYSTEM

6E-29

GA413
supple

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

Harmar Mobility AL001 Installation And Owner'S Manual preview
AL001
Бренд: Harmar Mobility Страницы: 10
DEFA WarmUp 411702 Fitting Instructions Manual preview
WarmUp 411702
Бренд: DEFA Страницы: 9
rough country Slim Line LED Light Grille Kit Manual preview
Slim Line LED Light Grille Kit
Бренд: rough country Страницы: 8
Actia TGU-R ACCESS User Manual preview
TGU-R ACCESS
Бренд: Actia Страницы: 37
Mazda 2007 MazdaSpeed6 Specification preview
2007 MazdaSpeed6
Бренд: Mazda Страницы: 12
Whelen Engineering Company FastTrax FTF4 Installation Manual preview
FastTrax FTF4
Бренд: Whelen Engineering Company Страницы: 9
STARLANE POLE STAR PRO Installation And Instruction Manual preview
POLE STAR PRO
Бренд: STARLANE Страницы: 24
Qeedon Higlow Series Product Instruction preview
Higlow Series
Бренд: Qeedon Страницы: 2
Thule RaceWay 991 Instructions Manual preview
RaceWay 991
Бренд: Thule Страницы: 12
Safe Fleet Prime Design OCM-3032 Quick Start Manual preview
Prime Design OCM-3032
Бренд: Safe Fleet Страницы: 4
WABCO TEBS E Manual preview
TEBS E
Бренд: WABCO Страницы: 224
iQOS CCU01 Safety Warnings And Instructions preview
CCU01
Бренд: iQOS Страницы: 4
Nos 05183NOS Owner'S Manual preview
05183NOS
Бренд: Nos Страницы: 22
VP Autoparts 419420 Installation preview
419420
Бренд: VP Autoparts Страницы: 2
Connects2 CTQIAU03 Installation & User Manual preview
CTQIAU03
Бренд: Connects2 Страницы: 2
VDO FUEL TANK GAUGE Installation Instructions Manual preview
FUEL TANK GAUGE
Бренд: VDO Страницы: 10
BMW 316I Owner'S Handbook Manual preview
316I
Бренд: BMW Страницы: 177
Volvo FH 6X2 Specifications preview
FH 6X2
Бренд: Volvo Страницы: 3

Бренды по названию

Популярные бренды

Загрузить еще бренды