Suzuki GA413 Скачать руководство пользователя страница 135 | Manualshive

Страница: 135 / 1246

background image

INSTALLATION

1) Check that vehicle’s front tires are at straight-ahead position

and if equipped with air bag system, contact coil is centered.
Refer to CENTERING CONTACT COIL of STEERING WHEEL
in this section.

For vehicle without air bag system

For vehicle with air bag system

1. Contact plate
2. Lugs
3. Grooves
4. Alignment marks

CAUTION:
For vehicle with air bag system
These two conditions are prerequisite for installation
of steering wheel. If steering wheel has been installed
without these conditions, contact coil will break when
steering wheel is turned.

2) For vehicle without air bag system

i) Apply grease to contact plate “A” of steering wheel.

GREASE: SUZUKI GREASE CE-T (99000-25290)

ii) Install steering wheel onto shaft, aligning them by matching

marks.

For vehicle with air bag system
Install steering wheel to steering shaft with 2 lugs on contact coil
fitted in two grooves in the back of steering wheel and also align-
ing marks on steering wheel and steering shaft.

3) Tighten steering shaft nut to specified torque.

Tightening Torque
(a): 33 N·m (3.3 kg-m, 24.0 lb-ft)

NOTE:
After installing the steering wheel, turn the steering wheel
about 1 full rotation so that the cancel cam pin fits into the
pin hole in the steering wheel and then check the turn sig-
nal lever for proper function.

4) For vehicle without air bag system

i) Install steering wheel pad in reverse order of removal.
ii) Connect negative cable at battery.
For vehicle with air bag system
Install driver air bag (inflator) module to steering wheel. Refer
to INSTALLATION of DRIVER AIR BAG (INFLATOR) MODULE
in this section.

STEERING WHEEL AND COLUMN

3C-7

«
...
133
134
135
136
137
...
»

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

Бренд: Dakota Digital Страницы: 2

Бренд: Dakota Digital Страницы: 7

Green Motion Building

Бренд: Eaton Страницы: 12

Бренд: Ignition Страницы: 1

Бренд: M7 SPEED Страницы: 11

Бренд: UMBRA RIMORCHI Страницы: 18

Бренд: Neuspeed Страницы: 2

Бренд: Gator Страницы: 8

StreetLine Series

Бренд: SAAS Страницы: 4

Бренд: POOL-LINE Страницы: 2

Бренд: Oldsmobile Страницы: 358

Бренд: Edelbrock Страницы: 2

Бренд: Mercedes-Benz Страницы: 93

Бренд: Mitsubishi Страницы: 490

Bounder turbo diesel 2001

Бренд: Fleetwood Страницы: 166

Бренд: Porsche Страницы: 145

PRIME DESIGN UXV 211

Бренд: Safe Fleet Страницы: 8

Бренд: 3SIXT Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды