Suzuki GA413 Скачать руководство пользователя страница 244 | Manualshive

Страница: 244 / 1246

background image

INSPECTION

Inspect all disassembled parts for wear or damage, and replace
parts if necessary.

NOTE:

Wash disassembled parts with brake fluid.

Do not reuse piston assembly.

Inspect master cylinder bore for scoring or corrosion. It is best to
replace corroded cylinder. Corrosion can be identified as pits or ex-
cessive roughness.

NOTE:
Polishing bore of master cylinder with cast aluminum body
with anything abrasive is prohibited, as damage to cylinder
bore may occur.

Rinse cylinder in clean brake fluid. Shake excess rinsing fluid from
cylinder. Do not use a cloth to dry cylinder, as lint from cloth cannot
be kept from cylinder bore surfaces.

[A]

[B]

[A] : For vehicle with ABS
[B] : For vehicle without ABS

ASSEMBLY

CAUTION:

Never use any mineral oil such as kerosene oil and
gasoline when washing and assembling parts.

Check inside of cylinder wall, pistons and cup seals
are free from any foreign objects such as dust and dirt
and use care not to cause any damage with a tool dur-
ing assembly.

Do not drop parts. Do not use any part which has been
dropped.

1) Apply brake fluid to inside of cylinder and contact surface of pis-

ton ass’y and insert secondary piston ass’y into cylinder body.
Be sure to install piston cup in correct installation direction and
straight into cylinder so that it is not caught.
Install secondary piston assembly into cylinder.

2) Install primary piston in cylinder.
3) Depress, and install circlip.

1. Rod
2. Circlip

4) Install piston stopper bolt with pistons pushed in all the way and

tighten it to specified torque.

Tightening Torque
(a) : 10N·m (1.0 kg-m, 7.5 Ib-ft)

1. Stopper bolt

5-48

BRAKES

«
...
242
243
244
245
246
...
»

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

Бренд: VanEssa mobilcamping Страницы: 8

Green Motion DC 22

Бренд: Eaton Страницы: 65

Бренд: Harmar Mobility Страницы: 10

Бренд: Vauxhall Страницы: 2

Бренд: Front Runner Страницы: 5

01 29 9 416 497

Бренд: BMW Страницы: 5

Бренд: Inbay Страницы: 20

Бренд: TBC Страницы: 12

Бренд: Prorack Страницы: 14

Бренд: TATA Motors Страницы: 236

Q Access Alpha GSE 2023

Бренд: Q Mobility Group Страницы: 9

Бренд: Hyundai Страницы: 280

Бренд: Whispbar Страницы: 14

1995 Cutlass Supreme

Бренд: Oldsmobile Страницы: 340

Бренд: RAM Страницы: 5

Бренд: CSL Страницы: 8

Бренд: Kuda Страницы: 3

Бренд: PERODUA Страницы: 43

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды