manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

DISASSEMBLY

1) Remove compressor.
2) Fix armature plate with special tool (A) and remove armature

plate screw.

Special Tool
(A): 09991-06060

NOTE:
Do not reuse armature plate screw.

1. Armature plate
2. Screw
3. Washer

3) Using special tool (B), remove armature plate.

Special Tool
(B): 09991-06030

1. Armature plate

4) Remove lead wire clamp.
5) Remove felt ring and shims from shaft.
6) Using special tool (C), remove circlip.

Special Tool
(C): 09900-06107

7) Remove magnet clutch lead wire clamp screw, and disconnect

magnet clutch read wire.

8) Remove magnet clutch with puller.

NOTE:
Be careful not to damage pulley when removing magnet
clutch.

1. Puller
2. Compressor

9) Remove circlip, then remove magnet clutch coil.

10) Remove front head mounting screw (10 pcs).

1. Front head

AIR CONDITIONING

1B-15

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

Suzuki SX4 SEDAN 2008 Owner'S Manual preview
SX4 SEDAN 2008
Бренд: Suzuki Страницы: 16
B-Speech B-Speech Prim Manual preview
B-Speech Prim
Бренд: B-Speech Страницы: 18
Jeep UNIVERSAL CJ-2A Operation Data preview
UNIVERSAL CJ-2A
Бренд: Jeep Страницы: 27
Jeep RENEGADE 2016 User Manual preview
RENEGADE 2016
Бренд: Jeep Страницы: 228
Jeep PATRIOT 2013 User Manual preview
PATRIOT 2013
Бренд: Jeep Страницы: 108
Jeep PATRIOT 2013 Owner'S Manual preview
PATRIOT 2013
Бренд: Jeep Страницы: 525
Metra Electronics 70-5511 Installation Instructions preview
70-5511
Бренд: Metra Electronics Страницы: 2
AC Schnitzer X3 M-Technik Fitting Instructions Manual preview
X3 M-Technik
Бренд: AC Schnitzer Страницы: 20
Rola LRSA2 Pack Contents & Fitting Instructions preview
LRSA2
Бренд: Rola Страницы: 3
Enduro autoSteady AS101 User Manual preview
autoSteady AS101
Бренд: Enduro Страницы: 48
TATA Motors Tata Indigo Diesel Owner'S Manual & Service Book preview
Tata Indigo Diesel
Бренд: TATA Motors Страницы: 190
Safe Fleet Prime Design HBR-E-FT33B Assembly Instructions Manual preview
Prime Design HBR-E-FT33B
Бренд: Safe Fleet Страницы: 12
Safe Fleet PRIME DESIGN URX-001-E Manual preview
PRIME DESIGN URX-001-E
Бренд: Safe Fleet Страницы: 8
Meta System FrontPlate4 Manual preview
FrontPlate4
Бренд: Meta System Страницы: 16
DFI VC230-BT Installation Manual preview
VC230-BT
Бренд: DFI Страницы: 6
WABCO TP19039 Manual preview
TP19039
Бренд: WABCO Страницы: 34
RAM Promaster 2016 User Manual preview
Promaster 2016
Бренд: RAM Страницы: 148
Hamron 619-626 User Instructions preview
619-626
Бренд: Hamron Страницы: 36

Бренды по названию

Популярные бренды

Загрузить еще бренды