manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

8) While tightening flange nut gradually with flange holder (special

tool) and power wrench, set preload of pinion to specification.

NOTE:

Before taking measurement with spring balance or
torque wrench, check for smooth rotation by hand.

Bevel pinion bearing preload is adjusted by tightening
bevel pinion nut to crush spacer.
Therefore, be sure to use a new spacer for adjustment
and tighten pinion nut step by step and check for starting
torque (preload) as often as tightening to prevent over
crushing of spacer.
If exceeds specification given below during adjustment,
replace spacer and repeat preload adjustment proce-
dure. Attempt to decrease starting torque (preload) by
loosening pinion nut will not do.

Pinion bearing preload: 5.0 – 13.0 kg-cm (4.4 – 11.2 Ib-in.)

Spring balance reading: 1.0 – 2.6 kg (2.3 – 5.7 Ib)

Special Tool
(A): 09922-75222
(G): 09922-66020

1. Power wrench (4 – 10 magnification)
2. Socket wrench
3. Spring balance
4. Torque wrench

Differential Case and Gears

1) After applying differential oil to side gear, pinions, pinion shaft,

washer and thrust washer, install them in differential case.

2) Measure thrust play of differential gear as follows.

Special Tool
(A): 09900-20606
(B): 09900-20701

Diff. gear thrust play: 0.01–0.37 mm (0.0004–0.014 in.)

Left side

Hold differential assembly with soft jawed vise and apply
measuring tip of dial gauge to top surface of gear.

Using 2 screwdrivers, move gear up and down and read
movement of dial gauge pointer.

1. Screwdriver
2. Differential gear

Left side

7F-10

DIFFERENTIAL

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

Qube AP1 Supplemental Instructions preview
AP1
Бренд: Qube Страницы: 19
Cadillac 2000 Warranty And Owner Assistance Information preview
2000
Бренд: Cadillac Страницы: 32
Jeda Wireless Pad Manual preview
Wireless Pad
Бренд: Jeda Страницы: 8
Jeep 2009 Wrangler Owner'S Manual preview
2009 Wrangler
Бренд: Jeep Страницы: 496
UMBRA RIMORCHI 39030 Installation Instructions Manual preview
39030
Бренд: UMBRA RIMORCHI Страницы: 18
IAG IAG-ENG-5003BK Instructions preview
IAG-ENG-5003BK
Бренд: IAG Страницы: 3
OCTO SmartDiag2GO GD201-O User Manual preview
SmartDiag2GO GD201-O
Бренд: OCTO Страницы: 5
TrailFX A4012S Installation Instructions Manual preview
A4012S
Бренд: TrailFX Страницы: 6
GMC SIERRA 2002 Manual preview
SIERRA 2002
Бренд: GMC Страницы: 499
Kia Amanti Owner'S Manual preview
Amanti
Бренд: Kia Страницы: 290
Chevrolet 2013 Spark Specifications preview
2013 Spark
Бренд: Chevrolet Страницы: 2
Globalsat MR-350P Installation Manual preview
MR-350P
Бренд: Globalsat Страницы: 2
Metra Electronics 99-8714 Installation Instructions Manual preview
99-8714
Бренд: Metra Electronics Страницы: 8
ULTIMATE SPEED 279746 Assembly And Safety Advice preview
279746
Бренд: ULTIMATE SPEED Страницы: 6
Yakima K614 Manual preview
K614
Бренд: Yakima Страницы: 12
FALCON RIDGE CF-1000-WD05 Instructions For Installation And Care preview
CF-1000-WD05
Бренд: FALCON RIDGE Страницы: 6
Skoda KAROQ 2017 Owner'S Manual preview
KAROQ 2017
Бренд: Skoda Страницы: 324
Elinchrom ELB 1200 User Manual preview
ELB 1200
Бренд: Elinchrom Страницы: 101

Бренды по названию

Популярные бренды

Загрузить еще бренды