manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

SDM

WARNING:
During service procedures, be very careful when han-
dling a Sensing and Diagnostic Module (SDM).
Be sure to read SERVICE PRECAUTIONS in this section
before starting to work and observe every precaution
during work. Neglecting them may result in personal in-
jury or inactivation of the air bag system when neces-
sary.

REMOVAL

1) Disconnect negative cable at battery.
2) Disable air bag system. Refer to DISABLING AIR BAG SYS-

TEM of SERVICE PRECAUTIONS in this section.

3) Remove console box by removing screws and clips.
4) Remove SDM cover.
5) Disconnect SDM connector from SDM.
6) Remove SDM (with SDM plate) as an assembly from vehicle.

NOTE:
Do not separate SDM and SDM plate.

INSPECTION

CAUTION:

Do not connect a tester whatever type it may be.

Never repair or disassemble SDM.

If SDM was dropped from a height of 90 cm (3 ft) or
more, it should be replaced.

Check SDM and SDM plate for dents, cracks or deformation.

Check SDM connector for damage, cracks or lock mechanism.

Check SDM terminal for bent, corrosion or rust.

If any faulty condition is found in above checks, replace.

INSTALLATION

For installation, reverse removal procedure, nothing following
points.

Tighten SDM bolts to specified torque.

Tightening Torque
(a): 6 N·m (0.6 kg-m, 4.5 lb-ft)

Connect SDM connector to SDM securely.

Enable air bag system. Refer to ENABLING AIR BAG SYSTEM
of SERVICE PRECAUTIONS in this section.

1. Console box
2. SDM cover
3. SDM
4. SDM bolt
5. SDM connector
6. Ground for air bag system

10B-44

AIR BAG SYSTEM

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

Taffio CH7102-FCX9 Quick Start Manual preview
CH7102-FCX9
Бренд: Taffio Страницы: 8
Paxton Automotive Novi Owner'S Installation Manual preview
Novi
Бренд: Paxton Automotive Страницы: 85
Thule 1489 Instructions Manual preview
1489
Бренд: Thule Страницы: 8
TATA Motors nano genX Owner'S Manual preview
nano genX
Бренд: TATA Motors Страницы: 156
Hyundai Santa Fe 2006 Owner'S Manual preview
Santa Fe 2006
Бренд: Hyundai Страницы: 280
StowAway 2 025.41 Assembly Instructions preview
025.41
Бренд: StowAway 2 Страницы: 2
Jaeger J05252127 Fitting Instructions Manual preview
J05252127
Бренд: Jaeger Страницы: 17
CrimeStopper CA-504.BRKT Install Manual preview
CA-504.BRKT
Бренд: CrimeStopper Страницы: 1
cam PFF Series Operating Manual preview
PFF Series
Бренд: cam Страницы: 28
SNIPER V2 Inox Owner'S Manual preview
V2 Inox
Бренд: SNIPER Страницы: 2
Ford Mustang 2007 Supplement Manual preview
Mustang 2007
Бренд: Ford Страницы: 40
Hama 00173884 Operating Instructions Manual preview
00173884
Бренд: Hama Страницы: 13
IOGear GBHFK201W6 User Manual preview
GBHFK201W6
Бренд: IOGear Страницы: 38
Setma E12PE27000 Instruction Manual preview
E12PE27000
Бренд: Setma Страницы: 13
Speedtech 64-67 Instructional Manual preview
64-67
Бренд: Speedtech Страницы: 12
Truma Mover S Installation & Operation Instructions preview
Mover S
Бренд: Truma Страницы: 16
Opel MERIVA 2014 Brochure & Specs preview
MERIVA 2014
Бренд: Opel Страницы: 44
Setma E12AU02002 Instruction Manual preview
E12AU02002
Бренд: Setma Страницы: 16

Бренды по названию

Популярные бренды

Загрузить еще бренды