manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

COOLING FAN

The cooling fan is driven by electric motor, and the motor is acti-
vated by ECM (and ECT sensor). For its details, refer to “ENGINE
AND EMISSION CONTROL SYSTEM” section.

WARNING:
Keep hands, tools and clothing away from engine cool-
ing fan to help prevent personal injury. This fan is electric
and can come on whether or not the engine is running.
The fan can start automatically in response to the ECM
(and ECT sensor) with the ignition switch in the “ON”
position.

1. Radiator
2. Cooling fan

COOLANT (WATER) TEMP. GAUGE (ECT
SENSOR)

Coolant temp. gauge is located at intake manifold. This gauge acti-
vates a water temp. meter in the instrument cluster.

1. ECT sensor
2. Generator
3. Intake manifold

ENGINE COOLING

6B-3

DIAGNOSIS

Condition

Possible Cause

Correction

Engine overheats

Loose or broken water pump belt

Not enough coolant

Faulty thermostat

Faulty water pump

Dirty or bent radiator fins

Coolant leakage on cooling system

Defective cooling fan motor or switch

Plugged radiator

Faulty radiator cap

Maladjusted ignition timing

Dragging brakes

Slipping clutch

Adjust or replace.

Check coolant level and add as necessary.

Replace.

Replace.

Clean or remedy.

Repair

Check and replace as necessary.

Check and replace radiator as necessary.

Replace.

Adjust.

Adjust brake.

Adjust or replace.

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

Camcar 40052 Mounting Instructions preview
40052
Бренд: Camcar Страницы: 6
Paxton Automotive Novi Owner'S Installation Manual preview
Novi
Бренд: Paxton Automotive Страницы: 85
Thule 1489 Instructions Manual preview
1489
Бренд: Thule Страницы: 8
Roadmaster Sterling ALL-TERRAIN 576 Owner'S Manual & Installation Instructions preview
Sterling ALL-TERRAIN 576
Бренд: Roadmaster Страницы: 12
Brodit ProClip 804438 Installation Instructions preview
ProClip 804438
Бренд: Brodit Страницы: 2
BGS technic 40108 Manual preview
40108
Бренд: BGS technic Страницы: 5
Oldsmobile 1999 88 Owner'S Manual preview
1999 88
Бренд: Oldsmobile Страницы: 344
ABL eMH3 Installation Manual preview
eMH3
Бренд: ABL Страницы: 66
Volkswagen 1973 Convertible Owner'S Manual preview
1973 Convertible
Бренд: Volkswagen Страницы: 80
Spiral Audio KT-FI001PB Nstallation Instructions preview
KT-FI001PB
Бренд: Spiral Audio Страницы: 2
Magneti Marelli 350203061230 Installation Instruction preview
350203061230
Бренд: Magneti Marelli Страницы: 2
SNIPER V2 Inox Owner'S Manual preview
V2 Inox
Бренд: SNIPER Страницы: 2
Thule 1809 Instruction Manual preview
1809
Бренд: Thule Страницы: 4
Mynew Portable Car Umbrella User Manual preview
Portable Car Umbrella
Бренд: Mynew Страницы: 5
Dodge 2004 JR41 Stratus Sedan Owner'S Manual preview
2004 JR41 Stratus Sedan
Бренд: Dodge Страницы: 273
Westfalia 17 56 46 Instruction Manual preview
17 56 46
Бренд: Westfalia Страницы: 2
Jacob Jensen Electronic Parking Disc 3 User Manual preview
Electronic Parking Disc 3
Бренд: Jacob Jensen Страницы: 17
Ranger design C24-DL Installation Manual preview
C24-DL
Бренд: Ranger design Страницы: 14

Бренды по названию

Популярные бренды

Загрузить еще бренды