manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

ALWAYS CARRY AIR BAG (INFLATOR) MODULE
WITH TRIM COVER (AIR BAG OPENING) AWAY
FROM BODY.

ALWAYS PLACE AIR BAG (INFLATOR) MODULE
ON WORKBENCH WITH TRIM COVER (AIR BAG
OPENING) UP, AWAY FROM LOOSE OBJECTS.

1. Slit on workbench
2. Workbench vise
3. Lower mounting bracket

0A1-4

GENERAL INFORMATION

SERVICING AND HANDLING

WARNING:
Many of service procedures require disconnection of “AIR
BAG” fuse and all air bag (inflator) module(s) from initiator
circuit to avoid an accidental deployment.
Driver and Passenger Air Bag (Inflator) Modules

D

For handling and storage of a live air bag (inflator) module,
select a place where the ambient temperature below 65

°

C

(150

°

F), without high humidity and away from electric

noise.

D

When carrying a live air bag (inflator) module, make sure
the bag opening is pointed away from you. In case of an
accidental deployment, the bag will then deploy with mini-
mal chance of injury. Never carry the air bag (inflator)
module by the wires or connector on the underside of the
module. When placing a live air bag (inflator) module on
a bench or other surface, always face the bag up, away
from the surface. As the live passenger air bag (inflator)
module must be placed with its bag (trim cover) facing up,
place it on the workbench with a slit or use the workbench
vise to hold it securely at its lower mounting bracket. This
is necessary so that a free space is provided to allow the
air bag to expand in the unlikely event of accidental de-
ployment. Otherwise, personal injury may result.

D

Never dispose of live (undeployed) air bag (inflator) mod-
ules (driver and passenger). If disposal is necessary, be
sure to deploy them according to deployment procedures
described in SECTION 10B before disposal.

D

The air bag (inflator) module immediately after deploy-
ment is very hot. Wait for at least half an hour to cool it off
before proceeding the work.

D

After an air bag (inflator) module has been deployed, the
surface of the air bag may contain a powdery residue. This
powder consists primarily of cornstarch (used to lubri-
cate the bag as it inflates) and by-products of the chemical
reaction. As with many service procedures, gloves and
safety glasses should be worn.

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

Jeep Liberty Quick Reference Manual preview
Liberty
Бренд: Jeep Страницы: 6
RAM 2500 2020 Quick Reference Manual preview
2500 2020
Бренд: RAM Страницы: 20
Saleen 10-8002-C11998B Installation Manual preview
10-8002-C11998B
Бренд: Saleen Страницы: 12
Buick 2013 Buick Verano Manual preview
2013 Buick Verano
Бренд: Buick Страницы: 5
Axxess AX-LR904 Installation Instructions Manual preview
AX-LR904
Бренд: Axxess Страницы: 8
SeaSucker SX6150 Quick Start Manual preview
SX6150
Бренд: SeaSucker Страницы: 9
Cadillac 2007 SRX Owner'S Manual preview
2007 SRX
Бренд: Cadillac Страницы: 522
Cadillac 2009 CTS Personalization Manual preview
2009 CTS
Бренд: Cadillac Страницы: 20
Cadillac 1999 DeVille Owner'S Manual preview
1999 DeVille
Бренд: Cadillac Страницы: 368
Luverne 205760 Installation Instructions preview
205760
Бренд: Luverne Страницы: 3
Navman B2+ User Manual preview
B2+
Бренд: Navman Страницы: 27
Thule Kit 2161 Fitting Instructions preview
Kit 2161
Бренд: Thule Страницы: 2
SAN HIMA SGBR015 Installation Instructions Manual preview
SGBR015
Бренд: SAN HIMA Страницы: 10
Subaru Impreza 2.5GT Specifications preview
Impreza 2.5GT
Бренд: Subaru Страницы: 2
Subaru 1999 Impreza Owner'S Manual preview
1999 Impreza
Бренд: Subaru Страницы: 328
RAM Ram 3500 2012 Specifications preview
Ram 3500 2012
Бренд: RAM Страницы: 13
v.link NAL-PC-HSD Manual preview
NAL-PC-HSD
Бренд: v.link Страницы: 21
Havis-Shields 1996-2008 Crown Victoria Driver and Passenger - Trunk Side Mounts C-TSM-CV-P Datasheet preview
1996-2008 Crown Victoria Driver and Passenger - Trunk Side Mounts C-TSM-CV-P
Бренд: Havis-Shields Страницы: 1

Бренды по названию

Популярные бренды

Загрузить еще бренды