manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

5) Install wheel and tighten wheel nuts to specified torque.

Tightening Torque
(a): 85 N·m (8.5 kg-m, 61.5 lb-ft)

6) Check to ensure that brake drum is free from dragging and

proper braking is obtained. Then remove vehicle from hoist and
preform brake test (foot brake and parking brake).

BRAKE SHOE

REMOVAL

1) Perform steps 1) to 6) of BRAKE DRUM REMOVAL.
2) Remove shoe return lower spring, upper spring and shoe hold

down spring by turning shoe hold down pins.

3) Remove brake shoes.

4) Disconnect parking brake shoe lever from parking brake cable.

1. Shoe hold down pins
2. Shoe hold down springs
3. Shoe return lower spring
4. Shoe return upper spring
5. Parking brake shoe lever

WARNING:
Use special care when removing brake shoe return
spring. Failure in its proper installation may allow it to
spring back and cause personal injury.

5) Remove retainer ring and disconnect parking brake shoe lever

from shoe rim.

1. Retainer ring
2. Parking brake

shoe lever

INSPECTION
Adjuster Assembly

Inspect ratchet or thread rod part for wear, sticking and corrosion.

5-40

BRAKES

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

Jeep UNIVERSAL CJ-2A Operation Data preview
UNIVERSAL CJ-2A
Бренд: Jeep Страницы: 27
Jeep RENEGADE 2016 User Manual preview
RENEGADE 2016
Бренд: Jeep Страницы: 228
Jeep PATRIOT 2013 User Manual preview
PATRIOT 2013
Бренд: Jeep Страницы: 108
Jeep PATRIOT 2013 Owner'S Manual preview
PATRIOT 2013
Бренд: Jeep Страницы: 525
LAS BC260 Operating Instructions Manual preview
BC260
Бренд: LAS Страницы: 44
LAS 11807 Operating Instructions Manual preview
11807
Бренд: LAS Страницы: 24
Zavoli Bora Technical Instructions And Installation Manual preview
Bora
Бренд: Zavoli Страницы: 26
Front Runner Easy-Out Fitting Instructions preview
Easy-Out
Бренд: Front Runner Страницы: 5
GMC SIERRA 2002 Manual preview
SIERRA 2002
Бренд: GMC Страницы: 499
Kia Amanti Owner'S Manual preview
Amanti
Бренд: Kia Страницы: 290
Eaton Green Motion DC 66 User Manual preview
Green Motion DC 66
Бренд: Eaton Страницы: 18
Harbor Freight Tools 66242 User Manual preview
66242
Бренд: Harbor Freight Tools Страницы: 12
Honda 0SR95-HL4-211A Installation Instructions preview
0SR95-HL4-211A
Бренд: Honda Страницы: 3
Havis-Shields 1996-2008 Crown Victoria Driver and Passenger - Trunk Side Mounts C-TSM-CV-P Datasheet preview
1996-2008 Crown Victoria Driver and Passenger - Trunk Side Mounts C-TSM-CV-P
Бренд: Havis-Shields Страницы: 1
v.LOGiC V5-CIC-E-PNP Manual preview
V5-CIC-E-PNP
Бренд: v.LOGiC Страницы: 22
Safe Fleet PRIME DESIGN HXR-269-E-UM3-80 Manual preview
PRIME DESIGN HXR-269-E-UM3-80
Бренд: Safe Fleet Страницы: 12
Streetwize SWGH3 Quick Start Manual preview
SWGH3
Бренд: Streetwize Страницы: 4
Volvo S90 - ACCESSORY PANEL Owner'S Manual Supplement preview
S90 - ACCESSORY PANEL
Бренд: Volvo Страницы: 166

Бренды по названию

Популярные бренды

Загрузить еще бренды