manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

5) In case of driver air bag (inflator) module:

i) Clear a space on the ground about 185 cm (6 feet) in diame-

ter where the driver air bag (inflator) module is to be
deployed. A paved, outdoor location where there is no activ-
ity is preferred. If an outdoor location is not available, a space
on the shop floor where there is no activity and sufficient ven-
tilation is recommended.
Ensure no loose or flammable objects are within the deploy-
ment area.

ii) Place the driver air bag (inflator) module, with its vinyl trim

cover facing up, on the ground in the space just cleared.

1. Driver air bag (inflator) module
2. Trim cover must face up
3. 185 cm (6 feet) of clearance

In case of passenger air bag (inflator) module
i) Clear a space on the ground about 185 cm (6 feet) in diame-

ter where the fixture (special tool) with attached air bag (infla-
tor) module is to be placed for deployment. A paved outdoor
location where there is no activity is preferred. If an outdoor
location is not available, a space on the shop floor where
there is no activity and sufficient ventilation is recom-
mended. Ensure that no loose or flammable objects are with-
in the deployment area.

ii) Place special tool (passenger air bag (inflator) module de-

ployment fixture) on the ground in the space cleared in step
i), if it has not already been placed there.

Special Tool 
(B): 09932-75041 or 09932-75040 and 09932-75050

iii) Fill plastic reservoir in fixture (special tool) with water or

sand. This is necessary to provide sufficient stabilization of
the fixture during deployment.

iv) Attach the passenger air bag (inflator) module in the fixture

(special tool) using mounting attachment, hold-down bolts
and nuts and M8 bolts and nuts.

Securely hand-tighten all fastener prior to deployment.

CAUTION:
Be sure to use the following bolt and nut for fixing
passenger air bag (inflator) module to mounting at-
tachment.   Size: M8, Strength: 7T

1. Trim cover must face up
2. 185 cm (6 feet) of clearance
3. Mounting attachment
4. M8 bolt and nut

AIR BAG SYSTEM

10B-49

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

Thule 1306 RAPID SYSTEM Fitting Instructions Manual preview
1306 RAPID SYSTEM
Бренд: Thule Страницы: 8
Wagan 2227-1 User Manual preview
2227-1
Бренд: Wagan Страницы: 8
Thermo King T- series Driver Manual To Simple Operation preview
T- series
Бренд: Thermo King Страницы: 2
Q Mobility Group Q Access Alpha GSE 2023 Installation Manual preview
Q Access Alpha GSE 2023
Бренд: Q Mobility Group Страницы: 9
Saab 12 787 887 Installation Instructions Manual preview
12 787 887
Бренд: Saab Страницы: 12
Subaru Impreza 2.5GT Specifications preview
Impreza 2.5GT
Бренд: Subaru Страницы: 2
Subaru 1999 Impreza Owner'S Manual preview
1999 Impreza
Бренд: Subaru Страницы: 328
Atera 080 705 User Information preview
080 705
Бренд: Atera Страницы: 3
Black Horse RB001BK Installation Instructions preview
RB001BK
Бренд: Black Horse Страницы: 5
Saab 32000574 Installation Instructions Manual preview
32000574
Бренд: Saab Страницы: 9
TATA Motors NEXON Owner'S Manual preview
NEXON
Бренд: TATA Motors Страницы: 232
Revelation lnd-10716 Installation Instructions preview
lnd-10716
Бренд: Revelation Страницы: 4
Axxess AXDSPX-TY3 Installation Instructions Manual preview
AXDSPX-TY3
Бренд: Axxess Страницы: 16
Mahindra 2016 Scorpio Owner'S Manual preview
2016 Scorpio
Бренд: Mahindra Страницы: 247
hager XEV1R22T2 Series Operating Instructions Manual preview
XEV1R22T2 Series
Бренд: hager Страницы: 14
Chevrolet 2003 Monte Carlo Owner'S Manual preview
2003 Monte Carlo
Бренд: Chevrolet Страницы: 386
Chevrolet 2003 Impala Owner'S Manual preview
2003 Impala
Бренд: Chevrolet Страницы: 410
Honda 2012 Civic Hybrid Technology Reference Manual preview
2012 Civic Hybrid
Бренд: Honda Страницы: 18

Бренды по названию

Популярные бренды

Загрузить еще бренды