manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

6) Stretch the deployment harness from the driver or passenger

air bag (inflator) module to its full length 10 m (33 ft).

Special Tool 
(A): 09932-75030

7) Place a power source near the shorted end of the deployment

harness. Recommended application: 12 Volts minimum, 2
amps minimum. A vehicle battery is suggested.

8) Verify that the area around the driver or passenger air bag (in-

flator) module is clear of all people and loose or flammable ob-
jects.

9) In case of driver air bag (inflater) module:

Verify that the driver air bag (inflator) module is resting with its
vinyl trim cover facing up.

In case of passenger air bag (inflator) module (if equipped):
Verify that the passenger air bag (inflator) module is firmly and
properly secured in passenger air bag (inflator) module de-
ployment fixture (special tool).

10) Connect the air bag (inflator) module to the deployment har-

ness connector and lock connector with lock lever.

11) Notify all people in the immediate area that you intend to

deploy the air bag (inflator) module.

NOTE:

When the air bag deploys, the rapid gas expansion will
create a substantial report. Wear suitable ear protec-
tion. Notify all people in the immediate area that you in-
tend to deploy the air bag (inflator) module and suitable
ear protection should be worn.

When the driver air bag deploys, driver air bag (inflator)
module may jump about 30 cm (1 ft) vertically. This is a
normal reaction of them to the force of the rapid gas ex-
pansion inside the air bag.

After the air bag (inflator) module has been deployed,
the surface of the air bag may contain a powdery resi-
due. This powder consists primarily of cornstarch
(used to lubricate the bag as it inflates) and byproducts
of the chemical reaction.

For driver air bag (inflator) module

For passenger air bag (inflator) module (if
equipped)

1. Stretch deployment harness to full length 10 m (33 ft).
2. Connect connectors.
3. Power source (12V vehicle battery)
4. Short the two deployment harness leads.

10B-50

AIR BAG SYSTEM

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

Porsche 911 GT3 - Brochure preview
911 GT3 -
Бренд: Porsche Страницы: 51
Whispbar K710W Fitting Instructions For Basic Carrier preview
K710W
Бренд: Whispbar Страницы: 14
Whispbar K448W Fitting Instructions Manual preview
K448W
Бренд: Whispbar Страницы: 15
Waeco 8885100124 Operating Manual preview
8885100124
Бренд: Waeco Страницы: 172
VBG 56-201901 Mounting Instructions preview
56-201901
Бренд: VBG Страницы: 16
Safe Fleet PRIME DESIGN VRR-NV200 Manual preview
PRIME DESIGN VRR-NV200
Бренд: Safe Fleet Страницы: 12
TAUBENREUTHER 29-T080301 Quick Start Manual preview
29-T080301
Бренд: TAUBENREUTHER Страницы: 8
Ford 2004 Freestar Workshop Manual preview
2004 Freestar
Бренд: Ford Страницы: 8
Intec CVD500LCD Installation And Operation Manual preview
CVD500LCD
Бренд: Intec Страницы: 16
Pyle PLDCP3 User Manual preview
PLDCP3
Бренд: Pyle Страницы: 2
Havis-Shields 1996-2008 Crown Victoria Driver and Passenger - Trunk Side Mounts C-TSM-CV-P Datasheet preview
1996-2008 Crown Victoria Driver and Passenger - Trunk Side Mounts C-TSM-CV-P
Бренд: Havis-Shields Страницы: 1
Prorack K577W Fitting Instructions Manual preview
K577W
Бренд: Prorack Страницы: 15
Volvo XC60 2014 Wiring Diagrams preview
XC60 2014
Бренд: Volvo Страницы: 362
Ford C-Max Energi 2014 Quick Reference Manual preview
C-Max Energi 2014
Бренд: Ford Страницы: 10
Ford TRANSIT 2015 Quick Reference Manual preview
TRANSIT 2015
Бренд: Ford Страницы: 8
Van Guard VG162S Fitting Instructions preview
VG162S
Бренд: Van Guard Страницы: 3
Tuff Tonneaus Bunji Ute Installation Instructions preview
Bunji Ute
Бренд: Tuff Tonneaus Страницы: 4
Honda 2007 Pilot Installation Instructions Manual preview
2007 Pilot
Бренд: Honda Страницы: 7

Бренды по названию

Популярные бренды

Загрузить еще бренды