manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

BRAKES

5-3

GENERAL DESCRIPTION

When the foot brake pedal is depressed, hydraulic pressure is developed in the master cylinder to actuate pistons
(two in front and four in rear).
The master cylinder is a tandem master cylinder. The brake pipes are connected to the master cylinder and they
make two independent circuits. One connects front  brakes (right and left) and the other connects rear brakes (right
and left).
The blend proportioning valve (B.P. valve) or the load sensing proportioning valve (LSPV) is included in these cir-
cuits between the master cylinder and rear wheels. In brake system of this model, the disc brake type is used of
the front wheel brake and a drum brake type (leading/trailing shoes) for the rear wheel brake.
The parking brake system is mechanical. It applies brake force to only rear wheels by means of the cable and me-
chanical linkage system. The same brake shoes are used for both parking and foot brakes.

NOTE:
“B.P.” valve in circuit diagram is installed on vehicle which is equipped with ABS and “LSPV” is installed
on vehicle not equipped with ABS.

[A] : For vehicle without ABS
[B] : For vehicle with ABS
1. Brake booster
2. Master cylinder
3. Secondary side
4. Primary side
5. Blend proportioning valve
6. 4-way joint
7. ABS hydraulic unit (actuator)
8. LSPV
9. 2-way joint

Forward

[A]

[B]

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

Jacob Jensen Electronic Parking Disc II User Manual preview
Electronic Parking Disc II
Бренд: Jacob Jensen Страницы: 28
KAP AUDI 4G HIGHEND Manual preview
AUDI 4G HIGHEND
Бренд: KAP Страницы: 20
Alpine eX-10 Owner'S Manual preview
eX-10
Бренд: Alpine Страницы: 69
Allen Sports S302 Instructions preview
S302
Бренд: Allen Sports Страницы: 2
Volvo 2004 V70 (Swedish) Användarmanual preview
2004 V70
Бренд: Volvo Страницы: 188
Eaton Green Motion DC 66 User Manual preview
Green Motion DC 66
Бренд: Eaton Страницы: 18
Zap XEBRA ZAPCAR Series Owner'S Manual preview
XEBRA ZAPCAR Series
Бренд: Zap Страницы: 16
PUTCO Molle Panels Assembly And Instruction Manual preview
Molle Panels
Бренд: PUTCO Страницы: 2
TrailFX 2123131 Quick User Manual preview
2123131
Бренд: TrailFX Страницы: 2
GReddy 12519101 Instruction Manual preview
12519101
Бренд: GReddy Страницы: 12
TATA Motors INDICA eV2 XETA CNG Supplemental Owner'S Manual preview
INDICA eV2 XETA CNG
Бренд: TATA Motors Страницы: 24
PAC AP4-GM61 Quick Start Manual preview
AP4-GM61
Бренд: PAC Страницы: 5
Percon Falcon 655 User Manual preview
Falcon 655
Бренд: Percon Страницы: 49
Billien OBU 5050 Quick Installation Manual preview
OBU 5050
Бренд: Billien Страницы: 2
Lexus ES 2021 Quick Manual preview
ES 2021
Бренд: Lexus Страницы: 28
Cadillac ESCALADE ESV 2005 Owner'S Manual preview
ESCALADE ESV 2005
Бренд: Cadillac Страницы: 482
curt CM-58967 Installation Manual preview
CM-58967
Бренд: curt Страницы: 4
Whispbar K684W Fitting Instructions Manual preview
K684W
Бренд: Whispbar Страницы: 15

Бренды по названию

Популярные бренды

Загрузить еще бренды