manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

FUEL PUMP

ON-VEHICLE INSPECTION

CAUTION:
When fuel filler cap is removed in any procedure, work
must be done in a well-ventilated area, keep away from
any open flames and without smoking.

1) Remove filler cap and turn ignition switch ON position. Then fuel

pump operating sound be heard from fuel filler for about 2 se-
conds and stop. Be sure to reinstall fuel filler cap after checking.
If above check result is not satisfactory, advance to “B-1 Fuel
Pump Circuit Check” in this section.

2) Fuel pressure should be felt at fuel return hose for 2 seconds

after turning ignition switch ON position.
If fuel pressure is not felt, advance to “B-3 Fuel Pressure Check”
in this section.

1. Fuel return hose
2. Air cleaner

REMOVAL/INSPECTION/INSTALLATION

Refer to “FUEL PUMP ASSEMBLY” in Section 6C.

1. Fuel pump

ENGINE AND EMISSION CONTROL SYSTEM

6E-63

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

Vauxhall Ampera Owner'S Manual preview
Ampera
Бренд: Vauxhall Страницы: 199
Blue Ox BX3781 Installation Instructions Manual preview
BX3781
Бренд: Blue Ox Страницы: 7
Shad NADSA ATV80 Owner'S Manual preview
NADSA ATV80
Бренд: Shad Страницы: 3
PUTCO MOLLE PANELS RAM 2500 Instruction Manual preview
MOLLE PANELS RAM 2500
Бренд: PUTCO Страницы: 4
Westfalia Portilo 350000 Installation And Operating Instructions Manual preview
Portilo 350000
Бренд: Westfalia Страницы: 18
FORM FIT SD 13R07-5 Installation Instructions preview
SD 13R07-5
Бренд: FORM FIT Страницы: 2
Thule Edge Flush Rail Instructions Manual preview
Edge Flush Rail
Бренд: Thule Страницы: 12
Trailboss HD86 Fitting Instructions preview
HD86
Бренд: Trailboss Страницы: 5
Eaton Green Motion DC 66 User Manual preview
Green Motion DC 66
Бренд: Eaton Страницы: 18
AA Products SR-A260 Instruction Manual preview
SR-A260
Бренд: AA Products Страницы: 4
Saab 12 787 887 Installation Instructions Manual preview
12 787 887
Бренд: Saab Страницы: 12
Elinchrom ELB 1200 User Manual preview
ELB 1200
Бренд: Elinchrom Страницы: 101
Jaeger 21010508J Fitting Instructions Manual preview
21010508J
Бренд: Jaeger Страницы: 14
Safe Fleet PRIME DESIGN UXV 211 Quick Start Manual preview
PRIME DESIGN UXV 211
Бренд: Safe Fleet Страницы: 8
3SIXT 3S-1802 Operating Instructions preview
3S-1802
Бренд: 3SIXT Страницы: 4
chinavasion CVTM-C163 User Manual preview
CVTM-C163
Бренд: chinavasion Страницы: 3
Axxess AXDSPX-TY3 Installation Instructions Manual preview
AXDSPX-TY3
Бренд: Axxess Страницы: 16
FALCON RIDGE CF-U-1000-RW02 Instructions For Installation And Care preview
CF-U-1000-RW02
Бренд: FALCON RIDGE Страницы: 8

Бренды по названию

Популярные бренды

Загрузить еще бренды