manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

ON-VEHICLE SERVICE

BATTERY

JUMP STARTING IN CASE OF EMERGENCY WITH
AUXILIARY (BOOSTER) BATTERY

Both booster and discharged battery should be treated carefully
when using jumper cables. Follow procedure outlined below, being
careful not to cause sparks.

1) Set parking brake and place automatic transmission in PARK

(NEUTRAL on manual transmission). Turn off ignition, turn off
lights and all other electrical loads.

2) Check electrolyte level. If it is below low level line, add distilled

water.

3) Attach end of one jumper cable to positive terminal of booster

battery and the other end of the same cable to positive terminal
of discharged battery. (Use 12-volt battery only to jump start en-
gine).

4) Attach one end of the remaining negative cable to negative ter-

minal of booster battery, and the other end to a solid engine
ground (such as exhaust manifold) at least 45 cm (18 in.) away
from battery of vehicle being started.

5) Start engine of vehicle with booster battery and turn off electrical

accessories. Then start engine of the vehicle with discharged
battery.

6) Disconnect jumper cables in the exact reverse order.

WARNING:

Departure from these conditions or procedure de-
scribed below could result in:
1) Serious personal injury (particularly to eyes) or

property damage from such causes as battery ex-
plosion, battery acid, or electrical burns.

2) Damage to electronic components of either vehicle.

Remove rings, watches, and other jewelry. Wear ap-
proved eye protection.

Be careful so that metal tools or jumper cables do not
contact positive battery terminal (or metal in contact
with it) and any other metal on vehicle, because a short
circuit could occur.

WARNING:
Do not connect negative cable directly to negative ter-
minal of dead battery.

6H-10

CHARGING SYSTEM

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

Cadillac 2011 CTS COUPE Personalization Manual preview
2011 CTS COUPE
Бренд: Cadillac Страницы: 20
Cadillac 2011 CTS COUPE Specifications preview
2011 CTS COUPE
Бренд: Cadillac Страницы: 2
Cadillac 2009 CTS Owner'S Manual preview
2009 CTS
Бренд: Cadillac Страницы: 494
Cadillac 2008 Escalade Owner'S Manual preview
2008 Escalade
Бренд: Cadillac Страницы: 500
Cadillac 2006 Escalade Warranty And Owner Assistance Information preview
2006 Escalade
Бренд: Cadillac Страницы: 40
Cadillac 2004 DeVille Owner'S Manual preview
2004 DeVille
Бренд: Cadillac Страницы: 432
Cadillac 1997 Catera Owner'S Manual preview
1997 Catera
Бренд: Cadillac Страницы: 338
Cadillac 2009 STS Get To Know preview
2009 STS
Бренд: Cadillac Страницы: 20
Cadillac 2005 STS Owner'S Manual preview
2005 STS
Бренд: Cadillac Страницы: 438
Gardigo MARTEN-FREE CAR Instruction Manual preview
MARTEN-FREE CAR
Бренд: Gardigo Страницы: 36
Triumph MAYFLOWER 1951 Instruction Book preview
MAYFLOWER 1951
Бренд: Triumph Страницы: 86
Code 3 21 COVERT Series Installation And Operation Instructions Manual preview
21 COVERT Series
Бренд: Code 3 Страницы: 16
Metra Electronics 99-3103 Installation Instructions preview
99-3103
Бренд: Metra Electronics Страницы: 2
BendPak Autostacker PL-6SR Installation And Operation Manual preview
Autostacker PL-6SR
Бренд: BendPak Страницы: 104
Meta System FrontPlate4 Manual preview
FrontPlate4
Бренд: Meta System Страницы: 16
Axxess AXRC-CH1 Installation Instructions Manual preview
AXRC-CH1
Бренд: Axxess Страницы: 8
Dodge Charger 1973 Body Service Manual preview
Charger 1973
Бренд: Dodge Страницы: 276
Bestop 51252 Installation Instructions preview
51252
Бренд: Bestop Страницы: 4

Бренды по названию

Популярные бренды

Загрузить еще бренды