manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

10B-34

AIR BAG SYSTEM

DTC B1051 – FRONTAL CRASH DETECTED (SYSTEM ACTIVATION 

COMMAND OUTPUTTED)

DTC WILL SET WHEN:
The SDM detects a frontal crash of sufficient force to warrant activation of the air bag system. (SDM outputs a de-
ployment command.)
TABLE TEST DESCRIPTION:
STEP 1:Check that DTC B1051 has been set although air bag has not been deployed.
STEP 2:Check that DTC has been set due to failure of SDM.
NOTE:
Before executing items in this table, be sure to perform AIR BAG DIAGNOSTIC SYSTEM CHECK.

STEP

ACTION

YES

NO

1

1) Ignition switch OFF.

2) Has air bag system deployed?

Replace components and
perform inspections as di-
rected in REPAIRS AND IN-
SPECTIONS REQUIRED AF-
TER AN ACCIDENT in this
section.

Go to step 2.

2

1) Inspect front of vehicle and undercar-

riage for signs of impact.

2) Are there signs of impact?

Replace components and
perform inspections as di-
rected in REPAIRS AND IN-
SPECTIONS REQUIRED AF-
TER AN ACCIDENT in this
section.

Substitute a known-good
SDM and recheck.

NOTE:
Upon completion of inspection and repair work, perform following items.
1) Reconnect all air bag system components, ensure all components are properly mounted.
2) Repeat AIR BAG DIAGNOSTIC SYSTEM CHECK to confirm that the trouble has been corrected.

DTC B1071 – INTERNAL SDM FAULT

DTC WILL SET WHEN:
An internal SDM fault is detected by SDM.

NOTE:
Before executing items below, be sure to perform AIR BAG DIAGNOSTIC SYSTEM CHECK.

NOTE:
DTC B1071 can never be cleared once it has been set.
1) Ignition switch OFF.
2) Replace SDM.
3) Repeat AIR BAG DIAGNOSTIC SYSTEM CHECK.

DTC B1013 – SYSTEM SPECIFICATIONS DIFFERENT FROM SDM 

SPECIFICATIONS

DTC WILL SET WHEN:
Specifications of the air bag system differ from those of SDM.

NOTE:
Before executing items below, be sure to perform AIR BAG DIAGNOSTIC SYSTEM CHECK.

1) Ignition switch OFF.
2) Replace SDM.
3) Repeat AIR BAG DIAGNOSTIC SYSTEM CHECK.

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

Suzuki Movano Owner'S Manual preview
Movano
Бренд: Suzuki Страницы: 353
Torklift F2012 Installation Instructions Manual preview
F2012
Бренд: Torklift Страницы: 16
Blue Giant STRONGARM RVR303 Installation & Technical Manual preview
STRONGARM RVR303
Бренд: Blue Giant Страницы: 48
Havis-Shields 1996-2008 Crown Victoria Driver and Passenger - Trunk Side Mounts C-TSM-CV-P Datasheet preview
1996-2008 Crown Victoria Driver and Passenger - Trunk Side Mounts C-TSM-CV-P
Бренд: Havis-Shields Страницы: 1
IOGear GBHFK201W6 User Manual preview
GBHFK201W6
Бренд: IOGear Страницы: 38
r.LiNK RL2-MMI3G-Q3 Manual preview
RL2-MMI3G-Q3
Бренд: r.LiNK Страницы: 21
Toyota Tundra guide Manual preview
Tundra guide
Бренд: Toyota Страницы: 672
Whispbar K723W Fitting Instructions Manual preview
K723W
Бренд: Whispbar Страницы: 77
TracRac TracVan Double Installation Instructions Manual preview
TracVan Double
Бренд: TracRac Страницы: 6
T-Tech FIT417 Service Bulletin preview
FIT417
Бренд: T-Tech Страницы: 1
Curt Group Aries 2074113 Installation Manual preview
Aries 2074113
Бренд: Curt Group Страницы: 2
TrailFX FCLR003B Assembly, Installation, Operation And Maintenance Instructions preview
FCLR003B
Бренд: TrailFX Страницы: 3
Westfalia 300025300113 Installation Instructions Manual preview
300025300113
Бренд: Westfalia Страницы: 97
Thule 1325 Kit Instructions Manual preview
1325 Kit
Бренд: Thule Страницы: 8
Saab 32 025 686 Installation Instructions Manual preview
32 025 686
Бренд: Saab Страницы: 9
Nav TV NTV-KIT041 Operation Instructions preview
NTV-KIT041
Бренд: Nav TV Страницы: 3
Jeep GRAND CHEROKEE L 2021 Owner'S Manual preview
GRAND CHEROKEE L 2021
Бренд: Jeep Страницы: 388
Toyota 2005 Camry ACV30 Series Wiring Diagram preview
2005 Camry ACV30 Series
Бренд: Toyota Страницы: 251

Бренды по названию

Популярные бренды

Загрузить еще бренды