Suzuki GA413 Скачать руководство пользователя страница 906 | Manualshive

Страница: 906 / 1246

background image

IDLE MIXTURE INSPECTION/ADJUSTMENT

(VEHICLE WITHOUT HEATED OXYGEN SEN-
SOR)

All vehicles not equipped with heated oxygen sensor are shipped
with their CO% factory adjusted as follows.

Idle mixture adjustment should never be changed from the original
factory setting. However, if during diagnosis, the check indicates
idle mixture to be the cause of a driver performance complaint or
emission failure, the idle mixture can be adjusted using the follow-
ing procedures.

NOTE:
For this inspection and adjustment, exhaust gas tester (CO
meter) and engine tachometer are necessary.

1. CO adjusting resistor

1) Check idle speed according to “Idle Speed Inspection” section.
2) Using exhaust gas tester, check that idle mixture CO% is within

above specification. If it is out of specification, adjust it to specifi-
cation by turning resistor knob.
NOTE:
CO adjusting resistor knob to “A” increases CO% (A/F mix-
ture becomes rich) and turning it to “B” decreases CO%
(A/F mixture becomes lean).

3) If idle mixture has been adjusted, confirm that idle speed is with-

in specification.

6E-14

ENGINE AND EMISSION CONTROL SYSTEM

GA413
supple

Engine idle mixture
(CO %)

0.5 – 1.5 % at specified idle speed

«
...
904
905
906
907
908
...
»

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

Бренд: JANE Страницы: 6

Бренд: Kathrein Страницы: 7

Бренд: Roav Страницы: 10

CHASSIS CAB 3500 2017

Бренд: RAM Страницы: 16

1997-2007 Dodge Dakota Telescoping Computer Base C-TCB-28

Бренд: Havis-Shields Страницы: 3

Бренд: XTC Страницы: 4

Бренд: Volvo Страницы: 42

Бренд: Classic AutoAir Страницы: 44

Бренд: Whispbar Страницы: 15

OUTLANDER PHEV 2022

Бренд: Mitsubishi MOTORS Страницы: 8

Бренд: ideus Страницы: 116

Бренд: AUTOTECH Страницы: 2

Бренд: Valueline Страницы: 40

Бренд: ULTIMATE SPEED Страницы: 56

Бренд: Kuda-Phonebase Страницы: 6

Бренд: iDataLink Страницы: 11

Бренд: RADICAL Страницы: 4

NANO CONNECT Smartview 72

Бренд: NanoCam Plus Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды