manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

SERVICING AND HANDLING

WARNING:
Many of service procedures require disconnection of
“AIR BAG” fuse and all air bag (inflator) module(s) from
initiator circuit to avoid an accidental deployment.
Driver and Passenger Air Bag (Inflator) Modules

For handling and storage of a live air bag (inflator)
module, select a place where the ambient temperature
below 65

C (150

F), without high humidity and away

from electric noise.

When carrying a live air bag (inflator) module, make
sure the bag opening is pointed away from you. In case
of an accidental deployment, the bag will then deploy
with minimal chance of injury. Never carry the air bag
(inflator) module by the wires or connector on the un-
derside of the module. When placing a live air bag (in-
flator) module on a bench or other surface, always face
the bag up, away from the surface. As the live passen-
ger air bag (inflator) module must be placed with its
bag (trim cover) facing up, place it on the workbench
with a slit or use the workbench vise to hold it securely
at its lower mounting bracket. This is necessary so
that a free space is provided to allow the air bag to ex-
pand in the unlikely event of accidental deployment.
Otherwise, personal injury may result.

Never dispose of live (undeployed) air bag (inflator)
modules (driver and passenger). If disposal is neces-
sary, be sure to deploy them according to deployment
procedures described in SECTION 10B before dispos-
al.

The air bag (inflator) module immediately after deploy-
ment is very hot. Wait for at least half an hour to cool
it off before proceeding the work.

After an air bag (inflator) module has been deployed,
the surface of the air bag may contain a powdery resi-
due. This powder consists primarily of cornstarch
(used to lubricate the bag as it inflates) and by-prod-
ucts of the chemical reaction. As with many service
procedures, gloves and safety glasses should be
worn.

ALWAYS CARRY AIR BAG (INFLATOR) MODULE
WITH TRIM COVER (AIR BAG OPENING) AWAY
FROM BODY.

ALWAYS PLACE AIR BAG (INFLATOR) MODULE
ON WORKBENCH WITH TRIM COVER (AIR BAG
OPENING) UP, AWAY FROM LOOSE OBJECTS.

1. Slit on workbench
2. Workbench vise
3. Lower mounting bracket

0A-4

GENGERAL INFORMATION

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

Jeda Wireless Pad Manual preview
Wireless Pad
Бренд: Jeda Страницы: 8
Jeep 2009 Wrangler Owner'S Manual preview
2009 Wrangler
Бренд: Jeep Страницы: 496
Kia Picanto 2015 Quick Reference Manual preview
Picanto 2015
Бренд: Kia Страницы: 10
Xpresskit DBALL2-HYUNDAI9 Installation And Quick Reference Manual preview
DBALL2-HYUNDAI9
Бренд: Xpresskit Страницы: 13
RAM 2011 3500 Chassis Cab User Manual preview
2011 3500 Chassis Cab
Бренд: RAM Страницы: 92
Mercedes-Benz AMG E-Class Supplement Manual preview
AMG E-Class
Бренд: Mercedes-Benz Страницы: 54
Toro 137-1019 Installation Instructions Manual preview
137-1019
Бренд: Toro Страницы: 24
Mercedes-Benz 2016 SLK Operator'S Manual preview
2016 SLK
Бренд: Mercedes-Benz Страницы: 358
Mercedes-Benz E55AMG Service Manual preview
E55AMG
Бренд: Mercedes-Benz Страницы: 39
Discount Car Stereo A2DIY-MBR Quick Start Bluetooth Installation Manual preview
A2DIY-MBR
Бренд: Discount Car Stereo Страницы: 8
Mopar 77072498AB Manual preview
77072498AB
Бренд: Mopar Страницы: 18
Mazda 2011 CX-9 Owner'S Manual preview
2011 CX-9
Бренд: Mazda Страницы: 605
Edelbrock 67312 Installation Instructions preview
67312
Бренд: Edelbrock Страницы: 2
Westfalia 17 56 46 Instruction Manual preview
17 56 46
Бренд: Westfalia Страницы: 2
HUSKY LINERS 47954 Installation Instructions preview
47954
Бренд: HUSKY LINERS Страницы: 4
iOttie HLCRIO138 Manual preview
HLCRIO138
Бренд: iOttie Страницы: 19
Whispbar K423W Fitting Instructions Manual preview
K423W
Бренд: Whispbar Страницы: 18
PEUGEOT 208 T16 User Manual preview
208 T16
Бренд: PEUGEOT Страницы: 67

Бренды по названию

Популярные бренды

Загрузить еще бренды