manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

6-54

ENGINE GENERAL INFORMATION AND DIAGNOSIS

GA413
supple

DTC P0134 (No.14) HEATED OXYGEN SENSOR (HO2S) CIRCUIT NO ACTIV-

ITY DETECTED (SENSOR-1)

WIRING DIAGRAM / CIRCUIT DESCRIPTION – Refer to DTC P0130 section.

DTC DETECTING CONDITION

POSSIBLE CAUSE

Engine warmed up.

While running under other than high load and high
engine speed conditions or at specified idle speed
(engine is closed loop condition), HO2S-1 output
voltage is high or low continuously.

2 driving cycle detection logic, Continuous monitor-
ing.

“RED” or “BLU/YEL” circuit open or short

Heated oxygen sensor malfunction

Fuel system malfunction

Exhaust gas leakage

DTC CONFIRMATION PROCEDURE – Refer to DTC P0130 section.

INSPECTION

STEP

ACTION

YES

NO

1

Was “ENGINE DIAG. FLOW TABLE” performed?

Go to Step 2.

Go to “ENGINE DIAG.
FLOW TABLE”.

2

Is there DTC(s) other than Fuel system 
(DTC P0171/P0172) and HO2S-1 (DTC P0134)?

Go to applicable DTC
Diag. Flow Table.

Go to Step 3.

3

Check HO2S-1 and Its Circuit.
1) Connect scan tool to DLC with ignition switch

OFF.

2) Warm up engine to normal operating tempera-

ture and keep it at 2000 r / min. for 60 sec.

3) Repeat racing engine (Repeat depressing ac-

celerator pedal 5 to 6 times continuously and
take foot off from pedal to enrich and enlean
A / F mixture).

Does HO2S-1 output voltage deflect between 0.3
V and over 0.6 V repeatedly?

Go to DTC P0171 and
P0172 Diag. Flow Table
(Fuel System Check).

Check “RED” and 
“BLU/YEL” wires for
open and short, and
connections for poor
connection. If wires and
connections are OK, re-
place HO2S-1.

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

Suzuki SX4 SEDAN 2008 Owner'S Manual preview
SX4 SEDAN 2008
Бренд: Suzuki Страницы: 16
Acdeos AXS FL Manual preview
AXS FL
Бренд: Acdeos Страницы: 38
Camcar 40000 Manual preview
40000
Бренд: Camcar Страницы: 6
Federal Signal Corporation Vision SLR Quick Disconnect Manual preview
Vision SLR
Бренд: Federal Signal Corporation Страницы: 8
Federal Signal Corporation Vision SLR Supplement Manual preview
Vision SLR
Бренд: Federal Signal Corporation Страницы: 8
Taffio CH7102-FCX9 Quick Start Manual preview
CH7102-FCX9
Бренд: Taffio Страницы: 8
Whispbar K783W Fitting Instructions Manual preview
K783W
Бренд: Whispbar Страницы: 16
FORM FIT SD 13R07-5 Installation Instructions preview
SD 13R07-5
Бренд: FORM FIT Страницы: 2
Thule Edge Flush Rail Instructions Manual preview
Edge Flush Rail
Бренд: Thule Страницы: 12
iDataLink BLADE-AL(TB)-TL2 Install Manual preview
BLADE-AL(TB)-TL2
Бренд: iDataLink Страницы: 9
Magneti Marelli BCF184 Installation Instructions preview
BCF184
Бренд: Magneti Marelli Страницы: 2
GMC Envoy XUV 2004 Getting To Know Manual preview
Envoy XUV 2004
Бренд: GMC Страницы: 20
Softride 26428 Instructions preview
26428
Бренд: Softride Страницы: 4
Magneti Marelli Obd Road User Manual preview
Obd Road
Бренд: Magneti Marelli Страницы: 9
Edelbrock 8135 Installation Instructions preview
8135
Бренд: Edelbrock Страницы: 4
Prime Design FEA-0004 Assembly Instructions Manual preview
FEA-0004
Бренд: Prime Design Страницы: 12
Kolpin 1466 Product Instructions preview
1466
Бренд: Kolpin Страницы: 6
Chevrolet LUMINA 1995 Owner'S Manual preview
LUMINA 1995
Бренд: Chevrolet Страницы: 324

Бренды по названию

Популярные бренды

Загрузить еще бренды