manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

6E-24

ENGINE AND EMISSION CONTROL SYSTEM

DTC NO.14 HEATED OXYGEN SENSOR CIRCUIT

(SIGNAL VOLTAGE LOW)

WIRING DIAGRAM

1. Heated oxygen sensor
2. Heated oxygen sensor connector
3. ECM connector (A)
4. ECM connector (B)
5. ECM
6. Power supply from main relay

TROUBLE SHOOTING

NOTE:

Before diagnosing trouble according to flow table given below, check to make sure that following system
and parts other than Electronic Fuel Injection system are in good condition.
– Air cleaner (clogged)
– Vacuum leaks (air inhaling)
– Spark plugs (contamination, gap)
– High-tension cords (crack, deterioration)
– Ignition timing
– Engine compression
– Any other system and parts which might affect A/F mixture or combustion.

If code No.14 and another code No. are indicated together, the latter has priority. Therefore, check and
correct what is represented by that code No. first and then proceed to the following check.

STEP

ACTION

YES

NO

1

Did you perform “ENGINE DIAGNOSTIC FLOW

TABLE” in Section 6?

Go to Step 2.

Go to“ENGINE DIAG-

NOSTIC FLOW TABLE”.

2

1) With ignition switch OFF position, install SUZU-

KI scan tool.

2) Start engine.
3) Run engine to normal operating temperature.
4) Maintain engine speed at 2000RPM for 60 se-

conds.

5) Using data list function of SUZUKI scan tool,

monitor oxygen sensor output voltage “02S”
with engine running at 2000RPM.

Does voltage switch below and above 0.55V?

Intermittent trouble.

If OK, substitute a

known-good ECM and

recheck.

Go to Step 3.

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

FORM FIT SD 13R07-5 Installation Instructions preview
SD 13R07-5
Бренд: FORM FIT Страницы: 2
Thule Edge Flush Rail Instructions Manual preview
Edge Flush Rail
Бренд: Thule Страницы: 12
Romik 2137 2D Installation Instructions Manual preview
2137 2D
Бренд: Romik Страницы: 6
Nav TV NAV-INREN Quick Manual preview
NAV-INREN
Бренд: Nav TV Страницы: 2
Harman Kardon DP 2US Quick Start Manual preview
DP 2US
Бренд: Harman Kardon Страницы: 16
TATA Motors TIAGO XZ 2019 Owner'S Manual preview
TIAGO XZ 2019
Бренд: TATA Motors Страницы: 184
B&G electronics PW-50C Civilian Installation And Operation Manual preview
PW-50C Civilian
Бренд: B&G electronics Страницы: 7
Dodge Dodge Challenger SRT8®Challenger SRT8 392 2012 Specifications preview
Dodge Challenger SRT8®Challenger SRT8 392 2012
Бренд: Dodge Страницы: 5
Edelbrock 65932 Installation Instructions preview
65932
Бренд: Edelbrock Страницы: 2
Ecco 5545A Installation And Operating Instructions Manual preview
5545A
Бренд: Ecco Страницы: 12
Softride 26428 Instructions preview
26428
Бренд: Softride Страницы: 4
Toyota SUPRA 1987 Electrical Wiring Diagram preview
SUPRA 1987
Бренд: Toyota Страницы: 165
National Cycle Quantum Wash'n'Wipe N30208 Assembly Instructions And Owner'S Manual preview
Quantum Wash'n'Wipe N30208
Бренд: National Cycle Страницы: 12
Whelen Engineering Company LED Dominator TAM83S2 Installation Manual preview
LED Dominator TAM83S2
Бренд: Whelen Engineering Company Страницы: 2
Ranger design 1525-PCX Installation Manual preview
1525-PCX
Бренд: Ranger design Страницы: 22
Honda 2000 Accord Sedan Online Reference Owner'S Manual preview
2000 Accord Sedan
Бренд: Honda Страницы: 320
Westin 28-21030 Instructions preview
28-21030
Бренд: Westin Страницы: 3
Tobe EPS-LD SafePark Technical Data preview
EPS-LD SafePark
Бренд: Tobe Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды