manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

1. Drive bevel pinion
2. Drive bevel pinion bearing

DIFFERENTIAL (FRONT)

7E-13

Necessary
shim thick-
ness

=

Dial gauge
measured
value

7) Install bevel pinion gauge block (special tool (7)) and then

install 0 (zero) adjusted bevel pinion mounting dummy shaft
assembly to differential front carrier.
Then read dial gauge.

NOTE:

D

Repeat turning back and force of dummy and measure
distance as far as top surface of pinion dummy accurate-
ly.

D

When dial gauge measuring tip extends from 0 (zero)
position, pointer turns counterclockwise.

D

Measured value may exceed 1 mm. Therefore, it is also
necessary to know reading of short pointer.

8) Obtain adjusting shim thickness by using measured value by

dial gauge in previous step.

9) Remove bevel pinion dummy from differential front carrier.

10) Select adjusting shim(s) (3) closest to value from among the

following available sizes and put it in place and then press-fit
rear bearing.

Special Tool
(A): 09941-74910

Available shim
thickness

1.15, 1.18, 1.21, 1.24,
1.27, 1.30 and 0.3 mm
(0.045, 0.046, 0.048, 0.049,
0.050, 0.051 and 0.012 in.)

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

ZAPTEC Go Quick Manual preview
Go
Бренд: ZAPTEC Страницы: 64
ZAPTEC Go Installation Manual preview
Go
Бренд: ZAPTEC Страницы: 24
Camcar 40000 Manual preview
40000
Бренд: Camcar Страницы: 6
Kargo Master 80070 Assembly Lnstructions preview
80070
Бренд: Kargo Master Страницы: 13
Kargo Master 4A96L Installation Manual preview
4A96L
Бренд: Kargo Master Страницы: 21
Kargo Master 40201 Installation Manual preview
40201
Бренд: Kargo Master Страницы: 4
Yakima Q46 Installation Instructions preview
Q46
Бренд: Yakima Страницы: 4
Napoli NPL-TV 7874 DIGITAL Instruction Manual preview
NPL-TV 7874 DIGITAL
Бренд: Napoli Страницы: 20
APS Auto Parts Specialist iBoard IB-ZK406 Installation Instructions preview
iBoard IB-ZK406
Бренд: APS Auto Parts Specialist Страницы: 3
Club Car Gasoline/Electric DS Golf Car 1996 Owner'S Manual preview
Gasoline/Electric DS Golf Car 1996
Бренд: Club Car Страницы: 48
B-Speech Pago INBTHF020 User Manual preview
Pago INBTHF020
Бренд: B-Speech Страницы: 24
Yuasa SmartShot Automatic 12V 1.5 Amp 5 Stage Technical Manual preview
SmartShot Automatic 12V 1.5 Amp 5 Stage
Бренд: Yuasa Страницы: 44
Whispbar K604W Fitting Instructions Manual preview
K604W
Бренд: Whispbar Страницы: 15
mtf TRANSPORT SYSTEM BackPower Manual preview
BackPower
Бренд: mtf TRANSPORT SYSTEM Страницы: 9
Kargo Master 8006A Instruction Manual preview
8006A
Бренд: Kargo Master Страницы: 19
Safe Fleet PRIME DESIGN VBR3-FT31B Manual preview
PRIME DESIGN VBR3-FT31B
Бренд: Safe Fleet Страницы: 12
Hyundai Entourage 2008 Quick Reference Manual preview
Entourage 2008
Бренд: Hyundai Страницы: 11
Mitsubishi MOTORS PAJERO SPORT Manual preview
PAJERO SPORT
Бренд: Mitsubishi MOTORS Страницы: 416

Бренды по названию

Популярные бренды

Загрузить еще бренды