manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

BRAKES

5-11

Symptom

Possible Cause

Remedy

Brake pull (Brakes

not working in

unison)

Pad linings and/or shoe linings are wet

with water or stained with oil in some

brakes.

Drum-to-shoe clearance out of adjust-

ment in some brakes.

(Malfunctioning auto adjusting mecha-

nism)

Disc and/or drum is out of round in some

brakes.

Wheel tires are inflated unequally.

Malfunctioning wheel cylinders.

Disturbed front end alignment.

Unmatched tires on same axle.

Restricted brake pipes or hoses.

Malfunctioning caliper assembly.

Loose suspension parts.

Loose calipers.

Maladjust brake booster push rod clevis.

Replace.

Check for inoperative auto adjusting

mechanism.

Replace.

Inflate equally.

Repair or replace.

Adjust as prescribed.

Tires with approximately the same

amount of tread should be used on the

same axle.

Check for soft hoses and damaged lines.

Replace with new hoses and new double-

walled steel brake tubing.

Check for stuck or sluggish pistons and

proper lubrication of caliper slide bush.

Caliper should slide.

Check all suspension mountings.

Check and torque bolts to specifications.

Check or adjust.

Noise (high pitched

squeak without brake

applied)

Front lining worn out.

Replace linings.

Rear brake locked

prematurely (For

vehicle equipped

with LSPV)

Maladjusted sensor spring length of

LSPV.

Malfunctioning LSPV assembly.

Check or adjust.

Replace assembly.

Brake locked (For

vehicle equipped

with ABS)

Malfunctioning ABS (Anti-lock Brake Sys-

tem).

Malfunctioning B.P. valve.

Check system referring to DIAGNOSIS of

Section 5E.

Replace.

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

Happy Orange USB-C Quick Start Manual preview
USB-C
Бренд: Happy Orange Страницы: 2
Daihatsu TERIOS J100 Maintenance Manual preview
TERIOS J100
Бренд: Daihatsu Страницы: 43
Lincoln 2015 MKS Owner'S Manual preview
2015 MKS
Бренд: Lincoln Страницы: 424
Volkswagen 1983 Camper Onwers Manual preview
1983 Camper
Бренд: Volkswagen Страницы: 26
Saleen 10-8002-C11998B Installation Manual preview
10-8002-C11998B
Бренд: Saleen Страницы: 12
Buick 2013 Buick Verano Manual preview
2013 Buick Verano
Бренд: Buick Страницы: 5
Porsche 911 GT3 - Owner'S Manual preview
911 GT3 -
Бренд: Porsche Страницы: 195
Jeep 2014 Grand Cherokee SRT8 Owner'S Manual preview
2014 Grand Cherokee SRT8
Бренд: Jeep Страницы: 596
Skoda 1K0 051 437 Assembly Instructions preview
1K0 051 437
Бренд: Skoda Страницы: 4
PAC Stinger ELEV8 Install Manual preview
Stinger ELEV8
Бренд: PAC Страницы: 14
Kolpin 98310 Product Instructions preview
98310
Бренд: Kolpin Страницы: 3
Hella AREIA 7040 Installation Instructions Manual preview
AREIA 7040
Бренд: Hella Страницы: 21
Draw tite 24963 Installation Instructions preview
24963
Бренд: Draw tite Страницы: 4
EFILive CM2350B User Manual preview
CM2350B
Бренд: EFILive Страницы: 25
Subaru Legacy 2011 Quick Reference Manual preview
Legacy 2011
Бренд: Subaru Страницы: 19
Joie i-Level Instruction Manual preview
i-Level
Бренд: Joie Страницы: 53
Scania Interlock 700 Series Instructions For Use Manual preview
Interlock 700 Series
Бренд: Scania Страницы: 82
v.link VL2-DVD900 Manual preview
VL2-DVD900
Бренд: v.link Страницы: 19

Бренды по названию

Популярные бренды

Загрузить еще бренды