manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

5E-20

ANTILOCK BRAKE SYSTEM (ABS) (OPTIONAL)

INSPECTION

STEP

ACTION

YES

NO

1

1) Remove all speed sensors.

2) Check each sensor for damage or foreign material being

attached to it.

Are they in good condition? (See Fig. 1.)

Go to step 2.

Clean or replace.

2

Check visually all wheel speed sensor installation hole for

the following.

Rotor serration (teeth) neither missing nor damaged.

No foreign material attached.

Rotor not being eccentric.

Wheel bearing free from excessive play.

Are they in good condition? (See Fig. 2.)

Go to step 3.

Clean, repair or

replace.

3

1) Install each speed sensor to each knuckle and / or axle

housing.

2) Tighten each sensor bolt to specified torque.

Is there any clearance between sensor and knuckle or axle

housing? (See Fig. 3)

Replace sensor.

Go to step 4.

4

Referring to item OUTPUT VOLTAGE INSPECTION of

FRONT WHEEL SPEED SENSOR, check output voltage or

waveform of each sensor.

Is proper output voltage or waveform available?

Go to step 5.

Replace sensor

and recheck.

5

Referring to item ABS HYDRAULIC UNIT OPERATION

CHECK in this section, check ABS hydraulic unit.

Is it in good condition?

Substitute a known-

good ABS hydraulic

unit / control module

assembly and recheck.

Replace ABS, 

hydraulic unit /

control module 

assembly.

Fig. 1

Fig. 2

Fig. 3

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

ULTIMATE SPEED CARBON Assembly And Safety Advice preview
CARBON
Бренд: ULTIMATE SPEED Страницы: 19
AccuAir AA-4397 Installation Manual preview
AA-4397
Бренд: AccuAir Страницы: 40
Peak PKC0RG Owner'S Manual preview
PKC0RG
Бренд: Peak Страницы: 10
Allen Sports QR545 Instructions preview
QR545
Бренд: Allen Sports Страницы: 2
Cadillac 2012 Escalade Hybrid Manual preview
2012 Escalade Hybrid
Бренд: Cadillac Страницы: 90
V8 equipment EBEX.2 Instruction Manual preview
EBEX.2
Бренд: V8 equipment Страницы: 17
TBC 645624 Instruction Manual preview
645624
Бренд: TBC Страницы: 12
Prorack K194 Fitting Instructions For Basic Carrier preview
K194
Бренд: Prorack Страницы: 14
Mitsubishi Fuso FK 2010 Owner'S Manual preview
Fuso FK 2010
Бренд: Mitsubishi Страницы: 362
Horn Tools HJIMRR02FIT Mounting Instructions preview
HJIMRR02FIT
Бренд: Horn Tools Страницы: 12
newmotion Dynamic Power Management Home - Module Installation Instruction preview
Dynamic Power Management Home - Module
Бренд: newmotion Страницы: 20
CARFACE CF145962E Instruction Manual preview
CF145962E
Бренд: CARFACE Страницы: 16
QA1 GS501 Installation Instructions preview
GS501
Бренд: QA1 Страницы: 3
Rhino-Rack S400-FK2 Instructions preview
S400-FK2
Бренд: Rhino-Rack Страницы: 2
Ford transit connect 2012 User Manual preview
transit connect 2012
Бренд: Ford Страницы: 299
Audi 2001 A3 Quick Reference Manual preview
2001 A3
Бренд: Audi Страницы: 4
Thule Brink 5324 Fitting Instructions Manual preview
Brink 5324
Бренд: Thule Страницы: 15
Setma E12PE27000 Instruction Manual preview
E12PE27000
Бренд: Setma Страницы: 13

Бренды по названию

Популярные бренды

Загрузить еще бренды