manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

6-88

ENGINE GENERAL INFORMATION AND DIAGNOSIS

GA413
supple

DTC P1450 BAROMETRIC PRESSURE SENSOR LOW/HIGH INPUT

DTC P1451 BAROMETRIC PRESSURE SENSOR PERFORMANCE PROBLEM

WIRING DIAGRAM / CIRCUIT DESCRIPTION
Barometric pressure sensor is installed in ECM.

DTC DETECTING CONDITION

POSSIBLE CAUSE

DTC P1450:

D

Barometric pressure sensor voltage is 4.7 V or higher, or
1.6 V or lower

D

ECM (barometric pressure sensor) malfunction

DTC P1451:

D

Vehicle stopped

D

Engine cranking

D

Difference between barometric pressure and intake 
manifold absolute pressure is 26 kPa, 200 mmHg or more.

D

Difference between intake manifold absolute pressure at
engine start and pressure after engine start is less than
1.3 kPa, 10 mmHg.

:

2 driving cycle detection logic, monitoring once/1 driving.

D

ECM (barometric pressure sensor) malfunction

DTC CONFIRMATION PROCEDURE
1) Turn ignition switch OFF.
2) Clear DTC with ignition switch ON.
3) Turn ignition switch ON for 2 sec., crank engine for 2 sec. and run it at idle for 1 min.
4) Check pending DTC in “PENDING DTC” mode and DTC in “DTC” mode.

INSPECTION

DTC P1450:
Substitute a known-good ECM and recheck.

DTC P1451:

NOTE:
Note that atmospheric pressure varies depending on weather conditions as well as altitude.
Take that into consideration when performing these check.

STEP

ACTION

YES

NO

1

Was “ENGINE DIAG. FLOW TABLE” performed?

Go to Step 2.

Go to “ENGINE DIAG.
FLOW TABLE” in this
section.

2

1) Connect scan tool to DLC with ignition switch

OFF.

2) Turn ignition switch ON and select “DATA LIST”

mode on scan tool.

3) Check manifold absolute pressure.
Is it barometric pressure (approx. 100 kPa, 
760 mmHg) at sea level?

Substitute a known-
good ECM and recheck.

Go to Step 3.

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

DANA TM4 SUMO MD MV Installation Manual preview
TM4 SUMO MD MV
Бренд: DANA Страницы: 42
dallara F305 Manual preview
F305
Бренд: dallara Страницы: 37
Yakima BOA Installation Instructions Manual preview
BOA
Бренд: Yakima Страницы: 8
RaceChip Pro 2 Installation Manual preview
Pro 2
Бренд: RaceChip Страницы: 12
Jeep 2014 Wrangler Owner'S Manual preview
2014 Wrangler
Бренд: Jeep Страницы: 673
Taffio CH7102-FCX9 Quick Start Manual preview
CH7102-FCX9
Бренд: Taffio Страницы: 8
Toyota 2011 Corolla LE Brochure preview
2011 Corolla LE
Бренд: Toyota Страницы: 19
GMC YUKON 2018 Owner'S Manual preview
YUKON 2018
Бренд: GMC Страницы: 425
Marlon Xplore Pro II SxS Owner’S Manual Assembly & Installation Instructions preview
Xplore Pro II SxS
Бренд: Marlon Страницы: 15
Gator HUDGPS1 Quick Start Manual preview
HUDGPS1
Бренд: Gator Страницы: 2
NavLinkz RL2-SC14 Manual preview
RL2-SC14
Бренд: NavLinkz Страницы: 21
Mobility Networks RPH 35.13 Use And Maintenance Manual preview
RPH 35.13
Бренд: Mobility Networks Страницы: 52
Oldsmobile 2000 Oldsmobile Intrigue Owner'S Manual preview
2000 Oldsmobile Intrigue
Бренд: Oldsmobile Страницы: 348
Prorack WHISPBAR S53 Fitting Instructions For Basic Carrier preview
WHISPBAR S53
Бренд: Prorack Страницы: 10
Skoda Fabia Combi 5J Fitting Instructions preview
Fabia Combi 5J
Бренд: Skoda Страницы: 2
Voxx Electronics CA-510a Installation Instructions Manual preview
CA-510a
Бренд: Voxx Electronics Страницы: 15
Volvo M3602654 Installation Instructions Manual preview
M3602654
Бренд: Volvo Страницы: 10
QA1 GS501 Installation Instructions preview
GS501
Бренд: QA1 Страницы: 3

Бренды по названию

Популярные бренды

Загрузить еще бренды