manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

DIAGNOSIS

The engine and emission control system in this vehicle are con-
trolled by ECM. ECM  has an On-Board Diagnostic system which
detects a malfunction in this system.
When diagnosing troubles, be sure to have full understanding of
the outline of “On-Board Diagnostic System” and each item in “Pre-
caution in Diagnosing Trouble” and execute diagnosis according
to “Engine Diagnostic Flow Table” in section 6.

ON-BOARD DIAGNOSTIC SYSTEM

ECM  performs on-board diagnosis (self-diagnosis) on the system
and operates “CHECK ENGINE” lamp (malfunction indicator lamp)
as follows.

Malfunction indicator lamp (“CHECK ENGINE” light) lights when
the ignition switch is turned ON position (but the engine at stop)
regardless of the condition of Engine and emission control sys-
tem. This is only to check the malfunction indicator lamp
(“CHECK ENGINE” light) bulb and its circuit.

If the areas monitored by ECM  is free from any trouble after the
engine start (while engine is running), malfunction indicator
lamp (“CHECK ENGINE” light) turns OFF.

When ECM detects a trouble which has occurred in the areas,
it makes malfunction indicator lamp (“CHECK ENGINE” light)
turn ON while the engine is running to warn the driver of such oc-
currence of trouble and at the same time it stores the exact
trouble area in ECM  back-up memory.

PRECAUTIONS IN DIAGNOSING TROUBLES

Before identifying diagnostic trouble code, don’t disconnect cou-
plers from ECM , battery cable from battery, ECM  ground wire
harness from engine. Such disconnection will erase memorized
trouble in ECM  memory.

Be sure to read “Precautions for Electrical Circuit Service” in
Section 0A before inspection and observe what is written there.

ECM  replacement
When substituting a known-good ECM , check for the following
conditions. Neglecting this check may cause damage to known-
good ECM .
– Resistance value of all relays, actuators is as specified re-
spectively.
– TP sensor and MAP sensor are in good condition and none of
power circuits of these sensors is shorted to ground.

ENGINE AND EMISSION CONTROL SYSTEM

6E-11

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

Front Runner Easy-Out Fitting Instructions preview
Easy-Out
Бренд: Front Runner Страницы: 5
Whispbar K448W Fitting Instructions Manual preview
K448W
Бренд: Whispbar Страницы: 15
Whispbar K728W Fitting Instructions Manual preview
K728W
Бренд: Whispbar Страницы: 85
Thule Kit 1429 Fitting Instructions Manual preview
Kit 1429
Бренд: Thule Страницы: 8
TATA Motors INDICA eV2 XETA CNG Supplemental Owner'S Manual preview
INDICA eV2 XETA CNG
Бренд: TATA Motors Страницы: 24
PAC AP4-GM61 Quick Start Manual preview
AP4-GM61
Бренд: PAC Страницы: 5
Percon Falcon 655 User Manual preview
Falcon 655
Бренд: Percon Страницы: 49
TATA Motors Indigo LE Owner'S Manual & Service Book preview
Indigo LE
Бренд: TATA Motors Страницы: 151
Thule QUICKDRAW RACHET TIE-DOWNS 855 User Manual preview
QUICKDRAW RACHET TIE-DOWNS 855
Бренд: Thule Страницы: 3
Master Tailgaters MR-43E2DVR1 User Manual preview
MR-43E2DVR1
Бренд: Master Tailgaters Страницы: 10
LedGlow Advanced Million Color Installation Instructions preview
Advanced Million Color
Бренд: LedGlow Страницы: 4
Altius ATHUDW-SCA User Manual preview
ATHUDW-SCA
Бренд: Altius Страницы: 16
Kuda-Phonebase 296570 Installation Instruction preview
296570
Бренд: Kuda-Phonebase Страницы: 6
Subaru XV Crosstrek Owner'S Manual preview
XV Crosstrek
Бренд: Subaru Страницы: 90
Mercedes-Benz CLS-Class Maintenance Booklet preview
CLS-Class
Бренд: Mercedes-Benz Страницы: 108
Husky 33094 Assembly, Installation, Operation And Maintenance Instructions preview
33094
Бренд: Husky Страницы: 18
Federal Signal Corporation DFC-WC-DUR21 Manual preview
DFC-WC-DUR21
Бренд: Federal Signal Corporation Страницы: 4
Lance 1130 Owner'S Manual preview
1130
Бренд: Lance Страницы: 132

Бренды по названию

Популярные бренды

Загрузить еще бренды