manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

WARNING:
When placing a live air bag (inflator) module on bench or
other surface, always face the bag up, away from the sur-
face. As the live passenger air bag (inflator) module must
be placed with its bag (trim cover) facing up, place it on
the workbench with a slit or use the workbench vise to
hold it securely at its lower mounting bracket.
It is also prohibited to place anything on top of the trim
cover and stack air bag (inflator) modules.
This is necessary so that a free space is provided to allow
the air bag to expand in the unlikely event of accidental
deployment.
Otherwise, personal injury may result.

ALWAYS PLACE AIR BAG (INFLATOR) MODULE
ON WORKBENCH WITH TRIM COVER (AIR BAG
OPENING) UP, AWAY FROM LOOSE OBJECTS.

1. Slit on workbench
2. Workbench vise
3. Lower mounting bracket

DEPLOYED AIR BAG (INFLATOR) MODULES

WARNING:

The air bag (inflator) module immediately after deploy-
ment is very hot. Wait for at least 30 minutes to cool it
off before proceeding the work.

Do not apply water, oil, etc. to deployed air bag (infla-
tor) module.

After an air bag (inflator) module has been deployed,
the surface of the air bag may contain a powdery resi-
due. This powder consists primarily of cornstarch
(used to lubricate the bag as it inflates) and byprod-
ucts of the chemical reaction. As with many service
procedures, gloves and safety glasses should be
worn.

Wash your hands with mild soap and water after com-
pleting the work.

Refer to the procedure described under DEPLOYED AIR BAG (IN-
FLATOR) MODULE DISPOSAL in this section.

10B-42

AIR BAG SYSTEM

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

Kathrein DDA Series User Manual preview
DDA Series
Бренд: Kathrein Страницы: 7
BrandMotion 1009-6503 Installation Instructions Manual preview
1009-6503
Бренд: BrandMotion Страницы: 8
Lexus LX 470 Owner'S Manual preview
LX 470
Бренд: Lexus Страницы: 369
Mountain Top Sports Bar Installation Manual preview
Sports Bar
Бренд: Mountain Top Страницы: 12
MAcarbon Ferrari 360 Map Carbon Light Installation Instructions preview
Ferrari 360 Map Carbon Light
Бренд: MAcarbon Страницы: 4
Yakima Landing Pad 24 Quick Start Manual preview
Landing Pad 24
Бренд: Yakima Страницы: 11
Mont Blanc ACTIVA+ Assembly Instructions preview
ACTIVA+
Бренд: Mont Blanc Страницы: 2
WABCO TEBS E Manual preview
TEBS E
Бренд: WABCO Страницы: 224
Belkin F8J034 User Manual preview
F8J034
Бренд: Belkin Страницы: 30
Mitsubishi FTO Series Handbook preview
FTO Series
Бренд: Mitsubishi Страницы: 141
Kolpin 1466 Product Instructions preview
1466
Бренд: Kolpin Страницы: 6
Truma Mover S Installation & Operation Instructions preview
Mover S
Бренд: Truma Страницы: 16
Curt Group Aries 2074113 Installation Manual preview
Aries 2074113
Бренд: Curt Group Страницы: 2
Audiovox Rear Observation System Package RVMPKG2 Installation Manual preview
Rear Observation System Package RVMPKG2
Бренд: Audiovox Страницы: 15
RAM Truck 2500 2018 Supplement Manual preview
Truck 2500 2018
Бренд: RAM Страницы: 32
Brodit 841488 Quick Start Manual preview
841488
Бренд: Brodit Страницы: 2
Camcar Walmec 40102 Manual preview
Walmec 40102
Бренд: Camcar Страницы: 6
BMW 330e Touring xDrive G21 2021 Owner'S Handbook Manual preview
330e Touring xDrive G21 2021
Бренд: BMW Страницы: 102

Бренды по названию

Популярные бренды

Загрузить еще бренды