manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

ASSEMBLING UNIT

1) Place bearing outer races on their respective bearings.

Used left and right outer races are not interchangeable.

2) Install case assembly in carrier.
3) Install side bearing adjusters on their respective carrier, making

sure adjuster are threaded properly.

NOTE:
Screw in each adjuster till it contacts bearing outer race so
that outer race is prevented from inclining.

4) Align match marks on cap and carrier. Screw in two side bearing

cap bolts two or three turns and press down bearing cap by
hand.

NOTE:
If bearing cap does not fit tightly on carrier, side bearing ad-
juster is not threaded properly. Reinstall adjuster.

Tighten cap bolts.

Provisional Tightening Torque
(a): 15 N·m (1.5 kg-m, 11.0 lb-ft)

1. Match mark

5) Tighten both bearing adjusters so as to obtain specified gear

backlash and at the same time, obtain preload of side bearing.
Special Tool
(A): 09930-40120 (Attachment)
(B): 09930-40113 (Rotor holder)
Bevel gear backlash: 0.10 – 0.20 mm (0.0039 – 0.0078 in.)

1. Bearing

adjuster

NOTE:

Be sure to apply measuring tip of dial gauge at right
angles to convex side (drive side) of tooth.

Measure at least 4 points on drive bevel gear periphery.

As a practical measure following would be recom-
mended to obtain specified backlash and side bearing
preload at the same time.
(1) To increase or decrease backlash for adjustment, dis-

place bevel gear toward or away from pinion by run-
ning in one adjuster and running out the other
adjuster by equal amount.

(2) Tighten both adjusters further by one notch at a time.

DIFFERENTIAL

7F-13

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

Toyota 2016 RAV4 Quick Reference Manual preview
2016 RAV4
Бренд: Toyota Страницы: 56
Cadillac 2012 Escalade Hybrid Manual preview
2012 Escalade Hybrid
Бренд: Cadillac Страницы: 90
Honda 2011 Civic Sedan Vehicle Instruction Card preview
2011 Civic Sedan
Бренд: Honda Страницы: 5
Suzuki 990E0-54P56-000 Installers And Users Instructions preview
990E0-54P56-000
Бренд: Suzuki Страницы: 12
Motoalliance VIPER MA11922 Install Instructions Manual preview
VIPER MA11922
Бренд: Motoalliance Страницы: 8
Cadillac 2007 SRX Owner'S Manual preview
2007 SRX
Бренд: Cadillac Страницы: 522
walser 30968 User Instructions preview
30968
Бренд: walser Страницы: 24
tams elektronik FCS-4 Manual preview
FCS-4
Бренд: tams elektronik Страницы: 19
Kargo Master 8006A Instruction Manual preview
8006A
Бренд: Kargo Master Страницы: 19
Safe Fleet PRIME DESIGN VBR3-FT31B Manual preview
PRIME DESIGN VBR3-FT31B
Бренд: Safe Fleet Страницы: 12
Qeedon Higlow Series Product Instruction preview
Higlow Series
Бренд: Qeedon Страницы: 2
FORM FIT 8F 00 Installation Instructions preview
8F 00
Бренд: FORM FIT Страницы: 2
Cadillac 2000 DeVille Service Manual Addendum preview
2000 DeVille
Бренд: Cadillac Страницы: 19
Audiovox Electronics HR7012M Installation Manual preview
HR7012M
Бренд: Audiovox Electronics Страницы: 12
GEMINI TECHNOLOGY 514F User Manual preview
514F
Бренд: GEMINI TECHNOLOGY Страницы: 9
Havis PT-A-502 Install Instructions preview
PT-A-502
Бренд: Havis Страницы: 4
Classic Accessories Quad Gear 18-029-010401-00-SC Instructions preview
Quad Gear 18-029-010401-00-SC
Бренд: Classic Accessories Страницы: 4
Jegs 41492 Installation Instructions preview
41492
Бренд: Jegs Страницы: 5

Бренды по названию

Популярные бренды

Загрузить еще бренды