manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

MATCHED TIRES AND WHEELS
(For vehicle equipped with steel wheels)

Tires and wheels are match mounted at the assembly plant.
This means that the radially stiffest part of the tire, or “high spot”,
is matched to the smallest radius or “low spot” of the wheel.
This is done to provide the smoothest possible ride.
The “high spot” of the tire is originally marked by paint dot on the
outboard sidewall. This paint dot will eventually wash off the tire.
The “low spot” of the wheel is originally marked by paint dot on the
wheel rim-flange. Properly assembled, the wheel rims’ paint dot
should be aligned with the tires’ paint dot as shown in left figure.
Whenever a tire is dismounted from its wheel, it should be re-
mounted so that the tire and wheel are matched. If the tire’s paint
dot cannot be located, a line should be scribed on the tire and
wheel before dismounting to assure that it is remounted in the
same position.

1. Paint

3F-4

WHEELS AND TIRES

MAINTENANCE AND MINOR ADJUSTMENTS

WHEEL AND TIRE

Wheel repairs that use welding, heating, or peening are not approved. All damaged wheels should be replaced.

STUDS

If a broken stud is found, see Section 3E (rear) or Section 3D (front) for Note and Replacement procedure.

INFLATION OF TIRES

The pressure recommended for any model is carefully calculated to give a satisfactory ride, stability, steering, tread
wear, tire life and resistance to bruises.
Tire pressure, with tires cold, (after vehicle has set for three hours or more, or driven less than one mile) should
be checked monthly or before any extended trip. Set to the specifications on the tire located on the driver’s side
door lock pillar.
It is normal for tire pressure increase when the tires become hot during driving. Do not bleed or reduce tire pressure
after driving. Bleeding reduces the “Cold Inflation Pressure.”

Higher than Recommended Pressure Can Cause:
1. Hard ride
2. Tire bruising or carcass damage
3. Rapid tread wear at center of tire

Unequal Pressure on Same Axle Can Cause:
1. Uneven braking
2. Steering lead
3. Reduced handling
4. Swerve on acceleration
Valve caps should be kept on valves to keep dust and
water out.

Lower than Recommended Pressure Can Cause:
1. Tire squeal on turns
2. Hard steering
3. Rapid and uneven wear on the edges of the tread
4. Tire rim bruises and rupture
5. Tire cord breakage
6. High tire temperatures
7. Reduced handling
8. High fuel consumption

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

Uebler F42 Mounting And Operating Instructions preview
F42
Бренд: Uebler Страницы: 18
Quadratec Brute Strength 12057.0271 Installation Manual preview
Brute Strength 12057.0271
Бренд: Quadratec Страницы: 6
Alpine eX-10 Installation Manual preview
eX-10
Бренд: Alpine Страницы: 8
WABCO TP2205 Installation Manual preview
TP2205
Бренд: WABCO Страницы: 48
Dometic Heki 2 Installation And Operating Manual preview
Heki 2
Бренд: Dometic Страницы: 158
Chevrolet LUMINA 1997 Owner'S Manual preview
LUMINA 1997
Бренд: Chevrolet Страницы: 376
Mazda 2008 CX-9 Brochure & Specs preview
2008 CX-9
Бренд: Mazda Страницы: 15
Whipple TOMAHAWK V1 Instruction Manual preview
TOMAHAWK V1
Бренд: Whipple Страницы: 3
Easee Home Wallbox Installation Instructions Manual preview
Home Wallbox
Бренд: Easee Страницы: 12
cam 40103 AL Mounting Instructions preview
40103 AL
Бренд: cam Страницы: 6
FALCON RIDGE Bobcat 3400 Instructions For Installation And Care preview
Bobcat 3400
Бренд: FALCON RIDGE Страницы: 4
Saturn 2007 Ion Owner'S Manual preview
2007 Ion
Бренд: Saturn Страницы: 440
Kogan CERTA CTCVINCVR14A User Manual preview
CERTA CTCVINCVR14A
Бренд: Kogan Страницы: 4
v.link CI-VL2-PC-HSD Manual preview
CI-VL2-PC-HSD
Бренд: v.link Страницы: 19
ULTIMATE SPEED 1188 1525 Instructions For Use And Safety Manuallines preview
1188 1525
Бренд: ULTIMATE SPEED Страницы: 26
Kargo Master 80070 Instruction Manual preview
80070
Бренд: Kargo Master Страницы: 17
Technaxx FMT1200BT User Manual preview
FMT1200BT
Бренд: Technaxx Страницы: 59
Prorack K442 Fitting Instructions Manual preview
K442
Бренд: Prorack Страницы: 15

Бренды по названию

Популярные бренды

Загрузить еще бренды