manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

STEERING LOWER SHAFT

1. Steering column
2. Steering lower shaft
3. Upper joint assembly
4. Upper joint bolt (column side)
5. Upper joint bolt (lower shaft side)
6. Lower joint bolt
7. Steering pinion shaft
8. Steering shaft seal
9. Marks

CAUTION:
For vehicle with air bag system
Never turn steering wheel while steering shaft lower joint
is removed.
Should it have been turned and contact coil (on combina-
tion switch) have got out of its centered position, it needs
to be centered again. Also, turning steering wheel more
than about two and a half turns will break contact coil.

REMOVAL

1) Turn steering wheel so that vehicle’s front tires are at straight-

ahead position.

2) Turn ignition switch to “LOCK” position and remove key.
3) Remove steering shaft seal from dash panel.
4) Make alignment marks on steering shaft and upper joint (“A”)

and steering lower shaft and pinion shaft (“B”) for a guide during
reinstallation.

5) Loosen upper joint bolt (lower shaft side) then remove upper

joint bolt (column side).

6) Move upper joint assembly to lower shaft side (in arrow direc-

tion in the figure).

7) Remove lower joint bolt.
8) Remove steering lower shaft and upper joint assembly.

INSTALLATION

1) Be sure that front wheels and steering wheel are in straight for-

ward state.

2) Align flat part “C” of steering lower shaft with bolt hole “D” of up-

per joint assembly as shown in the figure. Tighten upper joint
bolt (lower shaft side) by hand.

3) Insert lower shaft to pinion shaft with matching marks (“B”).
4) Tighten lower joint bolt (pinion side) to specified torque.

Tightening Torque
(a): 25 N·m (2.5 kg-m, 18.0 lb-ft)

5) Apply grease to “E” of steering shaft seal.

Grease: SUZUKI SUPER GREASE A (99000–25010)

6) Install steering shaft seal to dash panel.
7) Insert upper joint assembly into steering shaft (column side)

with matching marks (“A”).

1. Marks
2. Upper joint bolt 

(lower shaft side)

3. Lower joint bolt
4. Steering shaft seal

STEERING WHEEL AND COLUMN

3C-15

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

OEM Audio Reference Series Manual preview
Reference Series
Бренд: OEM Audio Страницы: 29
Ford 2008 Mustang Quick Reference Manual preview
2008 Mustang
Бренд: Ford Страницы: 2
Honda 08A28-0J6-800 Installation Instructions Manual preview
08A28-0J6-800
Бренд: Honda Страницы: 32
Xpresskit DBALL2-HYUNDAI9 Installation And Quick Reference Manual preview
DBALL2-HYUNDAI9
Бренд: Xpresskit Страницы: 13
RAM 2011 3500 Chassis Cab User Manual preview
2011 3500 Chassis Cab
Бренд: RAM Страницы: 92
Cadillac 54-6219 1954 Shop Manual preview
54-6219 1954
Бренд: Cadillac Страницы: 409
Fortin THAR-AUD1 Manual preview
THAR-AUD1
Бренд: Fortin Страницы: 9
BrandMotion FLTW-7511 Installation Manual preview
FLTW-7511
Бренд: BrandMotion Страницы: 6
GROM Audio VLINE Installation Manual preview
VLINE
Бренд: GROM Audio Страницы: 20
Bracketron Multi Vehicle Mount MVM-35-05 Installation Manual preview
Multi Vehicle Mount MVM-35-05
Бренд: Bracketron Страницы: 4
Rugged Ridge 13551.33 Manual preview
13551.33
Бренд: Rugged Ridge Страницы: 3
Brodit Heavy Duty ProClip Installation Instructions preview
Heavy Duty ProClip
Бренд: Brodit Страницы: 2
RADICAL R-C10AD2 Device Installation Manual preview
R-C10AD2
Бренд: RADICAL Страницы: 11
AUTOTECH 10.109.405K Installation Instructions preview
10.109.405K
Бренд: AUTOTECH Страницы: 2
Vauxhall Insignia 2009 Owner'S Manual preview
Insignia 2009
Бренд: Vauxhall Страницы: 253
Rajant 23-100068-001 Quick Start Manual preview
23-100068-001
Бренд: Rajant Страницы: 11
Vauxhall Signum Owner'S Manual preview
Signum
Бренд: Vauxhall Страницы: 310
Whispbar K536W Fitting Instructions Manual preview
K536W
Бренд: Whispbar Страницы: 17

Бренды по названию

Популярные бренды

Загрузить еще бренды