manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

3) Apply grease to axle shaft oil seal lip as shown.

“A”: Grease 99000-25010

4) Apply sealant to mating surface of axle housing with brake

back plate.

NOTE:
Make sure that old sealant was removed before applying
new one.

“B”: Sealant 99000-31110 or 99000-31090

1. Oil seal
2. Axle housing

5) Install rear axle shaft to rear axle housing.
6) Tighten brake back plate bolts to specified torque.

Tightening Torque
(a): 23 N·m (2.3 kg-m,17.0 lb-ft)

7) Install wheel cylinder, and tighten wheel cylinder bolts and

brake pipe flare nut (or nuts) to specified torque. (Refer to
steps 1) to 4) of WHEEL CYLINDER INSTALLATION).

8) Install parking brake cable to brake back plate.
9) Install brake shoes, referring to steps 1) and 3) of BRAKE

SHOE INSTALLATION.

10) Install brake drum. (Refer to steps 1) to 2) of BRAKE DRUM

INSTALLATION.

11) Refill differential housing with new specified gear oil. Refer to

MAINTENANCE SERVICE in Section 7F for refill.

12) Fill reservoir with brake fluid and bleed brake system. (For

bleeding operation, refer to BLEEDING BRAKES.)

13) Install wheel and tighten wheel nuts to specified torque.
14) Upon completion of all jobs, turn adjuster upward by flat-head

screw driver, depress brake pedal with about 30 kg (66 lbs)
load three to five times so as to obtain proper drum-to-shoe
clearance.
Adjust parking brake cable. (For adjustment, refer to PARK-
ING BRAKE CHECK AND ADJUSTMENT.)

15) Install console box.
16) Check to ensure that brake drum is free from dragging and

proper braking is obtained. Then remove vehicle from hoist
and perform brake test (foot brake and parking brake).

17) Check each installed part for oil leakage.

1. Stopper ring
2. Brake back plate

5-44

BRAKES

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

Camcar 40052 Mounting Instructions preview
40052
Бренд: Camcar Страницы: 6
Ford E-Transit 2022 Manual preview
E-Transit 2022
Бренд: Ford Страницы: 22
ULTIMATE SPEED 94600 Assembly And Safety Advice preview
94600
Бренд: ULTIMATE SPEED Страницы: 21
Dakota Digital LED Tail Lights for 1959 Chevrolet Impala, Bel Air, Biscayne... Installation Instructions preview
LED Tail Lights for 1959 Chevrolet Impala, Bel Air, Biscayne...
Бренд: Dakota Digital Страницы: 3
Brodit ProClip 854208 Manual preview
ProClip 854208
Бренд: Brodit Страницы: 2
Black Horse Off Road TO20 Installation Instructions Manual preview
TO20
Бренд: Black Horse Off Road Страницы: 7
rough country 921107830 Installation Instruction preview
921107830
Бренд: rough country Страницы: 4
Ferve F-2024 Operating Instructions Manual preview
F-2024
Бренд: Ferve Страницы: 28
Federal Signal Corporation Cuda TriOptic 351014F Series Instruction Sheet preview
Cuda TriOptic 351014F Series
Бренд: Federal Signal Corporation Страницы: 4
Kia Magentis 2002 Owner'S Manual preview
Magentis 2002
Бренд: Kia Страницы: 216
Cadillac CTS 2011 Manual preview
CTS 2011
Бренд: Cadillac Страницы: 78
Yakima K1043 Manual preview
K1043
Бренд: Yakima Страницы: 10
Kargo Master PRO-IV Assembly Instructions Manual preview
PRO-IV
Бренд: Kargo Master Страницы: 8
Honda 2005 Civic Owner'S Manual preview
2005 Civic
Бренд: Honda Страницы: 234
TOP VEHICLE TECH GRKRT01 Installation Manual preview
GRKRT01
Бренд: TOP VEHICLE TECH Страницы: 8
Air Lift RideControl 59540 Manual preview
RideControl 59540
Бренд: Air Lift Страницы: 10
Ford 2007 Explorer Owner'S Manual preview
2007 Explorer
Бренд: Ford Страницы: 722
Genesis G90 Simple Manual preview
G90
Бренд: Genesis Страницы: 18

Бренды по названию

Популярные бренды

Загрузить еще бренды