manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

AIR BAG SYSTEM

10B-9

AIR BAG DIAGNOSTIC SYSTEM CHECK

WARNING:
To avoid deployment when troubleshooting the air bag system, do not use electrical test equipment
such as a battery powered or AC powered voltmeter, ohmmeter, etc., or any type of electrical equip-
ment other than that specified in this manual. Do not use a non-powered probe type tester.
Instructions in this manual must be followed carefully, otherwise personal injury may result.

CAUTION:
The order in which diagnostic trouble codes are diagnosed is very important. Failure to diagnose
the diagnostic trouble codes in the order specified may result in extended diagnostic time, incorrect
diagnosis and incorrect parts replacement.

The diagnostic procedures used in this section are designed to find and repair air bag system malfunctions.
To get the best results, it is important to use the diagnostic flow tables and follow the sequence listed below.

1) Perform the AIR BAG DIAGNOSTIC SYSTEM CHECK FLOW TABLE.

(The AIR BAG DIAGNOSTIC SYSTEM CHECK FLOW TABLE must be the starting point of any air bag system
diagnosis.
The AIR BAG DIAGNOSTIC SYSTEM CHECK FLOW TABLE checks for proper “AIR BAG” warning lamp op-
eration through “AIR BAG” warning lamp and whether air bag diagnostic trouble codes exist.)

2) Refer to the proper diagnostic table as directed by the AIR BAG DIAGNOSTIC SYSTEM CHECK FLOW TABLE.

(The AIR BAG DIAGNOSTIC SYSTEM CHECK FLOW TABLE will lead you to the correct table to diagnose any
air bag system malfunctions. Bypassing these procedures may result in extended diagnostic time, incorrect
diagnosis and incorrect parts replacement.)

3) Repeat the AIR BAG DIAGNOSTIC SYSTEM CHECK FLOW TABLE after any repair or diagnostic procedures

have been performed.
(Performing the AIR BAG DIAGNOSTIC SYSTEM CHECK FLOW TABLE after all repair or diagnostic proce-
dures will ensure that the repair has been made correctly and that no other malfunctions exist.)

FLOW TABLE TEST DESCRIPTION
STEP1: Check that “AIR BAG” warning lamp lights.
STEP2: Check that “AIR BAG” warning lamp lights.
STEP3: Check diagnosis switch circuit.
STEP4: Check that “AIR BAG” warning lamp flashes 6 times after ignition switch is turned ON.
STEP5: Check that history codes are in SDM memory.
STEP6: Check that current code is in SDM memory.

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

Buick 2005 Terraza Owner'S Manual preview
2005 Terraza
Бренд: Buick Страницы: 428
GReddy Intercooler Kit Type 31 Installation Manual preview
Intercooler Kit Type 31
Бренд: GReddy Страницы: 9
Eaton Green Motion DC 66 User Manual preview
Green Motion DC 66
Бренд: Eaton Страницы: 18
Metra Electronics 99-5819 Installation Instructions Manual preview
99-5819
Бренд: Metra Electronics Страницы: 8
Thule 1597 Instructions preview
1597
Бренд: Thule Страницы: 4
Edelbrock 5756 Installation Instructions preview
5756
Бренд: Edelbrock Страницы: 1
Menabo YELO 4 NS Fitting Instructions Manual preview
YELO 4 NS
Бренд: Menabo Страницы: 8
Butts of Bawtry TBT4700 Quick Start Manual preview
TBT4700
Бренд: Butts of Bawtry Страницы: 2
Belkin LineCast Auto FM User Manual preview
LineCast Auto FM
Бренд: Belkin Страницы: 15
Rover 75 Saloon Owner'S Handbook Manual preview
75 Saloon
Бренд: Rover Страницы: 285
Xpresskit 20110601 Installation Manual preview
20110601
Бренд: Xpresskit Страницы: 12
Volkswagen 1963 1500 Instruction Manual preview
1963 1500
Бренд: Volkswagen Страницы: 68
Magneti Marelli AC911 Installation Instruction preview
AC911
Бренд: Magneti Marelli Страницы: 3
ACV 381190-37-1 Installation Manual preview
381190-37-1
Бренд: ACV Страницы: 2
Mercedes-Benz SLK 350 Brochure preview
SLK 350
Бренд: Mercedes-Benz Страницы: 24
Whispbar K477W Fitting Instructions Manual preview
K477W
Бренд: Whispbar Страницы: 15
Cadillac ESCALADE EXT - DATASHEET 2011 Datasheet preview
ESCALADE EXT - DATASHEET 2011
Бренд: Cadillac Страницы: 1
ABB InCharge Terra AL2-40-240-T1-WC1R Installation Manual preview
InCharge Terra AL2-40-240-T1-WC1R
Бренд: ABB Страницы: 39

Бренды по названию

Популярные бренды

Загрузить еще бренды