manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

PRECAUTIONS

PRECAUTIONS FOR VEHICLE EQUIPPED
WITH A SUPPLEMENTAL RESTRAINT
(AIR BAG) SYSTEM

WARNING:

The configuration of air bag system parts are as
shown in the figure. When it is necessary to service
(remove, reinstall and inspect) these parts, be sure to
follow procedures described in SECTION 10B. Failure
to follow proper procedures could result in possible
air bag system activation, personal injury, damage to
parts or air bag system being unable to activate when
necessary.

If the air bag system and another vehicle system both
need repair, SUZUKI recommends that the air bag sys-
tem be repaired first, to help avoid unintended air bag
system activation.

Do not modify the steering wheel, dashboard, or any
other air bag system components. Modifications can
adversely affect air bag system performance and lead
to injury.

If the vehicle will be exposed to temperatures over
93

C (200

F) (for example, during a paint baking pro-

cess), remove the air bag system components before-
hand to avoid component damage or unintended air
bag system activation.

1. Steering wheel
2. Driver air bag (inflator) module
3. Passenger air bag (inflator) module (if equipped)
4. SDM
5. Air bag harness
6. DLC

DIAGNOSIS

When troubleshooting air bag system, be sure to follow
DIAGNOSIS in SECTION 10B. Bypassing these procedures
may result in extended diagnostic time, incorrect diagno-
sis, and incorrect parts replacement.

Never use electrical test equipment other than that speci-
fied in this manual.

WARNING:
Never attempt to measure the resistance of the air bag
(inflator) modules (driver and passenger). It is very dan-
gerous as the electric current from the tester may deploy
the air bag.

GENERAL INFORMATION

0A-3

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

Warrior Products 10936 Installation Instructions preview
10936
Бренд: Warrior Products Страницы: 3
Kuda-Phonebase 055040 Installation Instruction preview
055040
Бренд: Kuda-Phonebase Страницы: 3
Blue Ox BX3781 Installation Instructions Manual preview
BX3781
Бренд: Blue Ox Страницы: 7
Shad NADSA ATV80 Owner'S Manual preview
NADSA ATV80
Бренд: Shad Страницы: 3
Camcar 40108 Mounting Instructions preview
40108
Бренд: Camcar Страницы: 6
ABL eMH3 Quick Start Manual preview
eMH3
Бренд: ABL Страницы: 4
Ford Focus ST 2018 Supplement Manual preview
Focus ST 2018
Бренд: Ford Страницы: 38
Monacor Carpower CAP-20 Quick Manual preview
Carpower CAP-20
Бренд: Monacor Страницы: 2
Enduro autoSteady AS101 User Manual preview
autoSteady AS101
Бренд: Enduro Страницы: 48
Waeco 8885100124 Operating Manual preview
8885100124
Бренд: Waeco Страницы: 172
VBG 56-201901 Mounting Instructions preview
56-201901
Бренд: VBG Страницы: 16
Omix-Ada 11704.05 Owner'S Manual preview
11704.05
Бренд: Omix-Ada Страницы: 6
Jeep WRANGLER 2017 User Manual preview
WRANGLER 2017
Бренд: Jeep Страницы: 292
Safe Fleet PRIME DESIGN HRR3-E-PM52 Manual preview
PRIME DESIGN HRR3-E-PM52
Бренд: Safe Fleet Страницы: 12
Painless Performance VORTEC 60211 Installation Instructions Manual preview
VORTEC 60211
Бренд: Painless Performance Страницы: 16
EUFAB 11439 Assembly preview
11439
Бренд: EUFAB Страницы: 8
Valueline SVL-CARCAM11 User Manual preview
SVL-CARCAM11
Бренд: Valueline Страницы: 40
L.A. West Sprinter Shuttle Owner'S Manual preview
Sprinter Shuttle
Бренд: L.A. West Страницы: 30

Бренды по названию

Популярные бренды

Загрузить еще бренды