manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

3) If equipped with passenger air bag (inflator) module, connect

Yellow connector of passenger air bag (inflator) module, and be
sure to lock connector with lock lever.
i) Connect connector.
ii) Lock connector with lock lever.

4) Install glove box.
5) Install “AIR BAG” fuse to fuse box.
6) Turn ignition switch to ON position and verify that “AIR BAG”

warning lamp flashes 6 times and then turns OFF.
If it does not operate as described, perform AIR BAG DIAG-
NOSTIC SYSTEM CHECK in this section.

1. Yellow connector of passenger air bag (inflator) module

(if equipped)

2. Steering support member
3. Harness cover

HANDLING AND STORAGE

SDM

WARNING:
Never power up air bag system when SDM is not rigidly
attached to the vehicle. Otherwise, personal injury may
result.

CAUTION:
After detecting one time of such collision as to meet de-
ployment conditions, the SDM must not be used.
Refer to AIR BAG DIAGNOSTIC SYSTEM CHECK when
checking the SDM.

Never attempt disassembly of SDM.

When storing SDM, select a place where neither high tempera-
ture nor high humidity is anticipated and oil, water and dust are
kept off.

If SDM was dropped from a height of 90 cm (3 ft) or more or if
it is found to be damaged or deformed, replace it with a new one.

If installation part of SDM was damaged, repair that part com-
pletely before reinstallation.

All SDM and mounting bracket fasteners must be carefully
torqued and the arrow must be pointed toward the front of the
vehicle to ensure proper operation of the air bag system.

1. SDM

10B-40

AIR BAG SYSTEM

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

Doug Thorley Headers THY-464-1 Instructions preview
THY-464-1
Бренд: Doug Thorley Headers Страницы: 5
Edelbrock 66002 Installation Instructions preview
66002
Бренд: Edelbrock Страницы: 2
Chevrolet 2013 Spark Specifications preview
2013 Spark
Бренд: Chevrolet Страницы: 2
Cadillac 2007 CTS Owner'S Manual preview
2007 CTS
Бренд: Cadillac Страницы: 518
Opel OPEL INSIGNIA Infotainment Manual preview
OPEL INSIGNIA
Бренд: Opel Страницы: 141
Rola LRSA2 Pack Contents & Fitting Instructions preview
LRSA2
Бренд: Rola Страницы: 3
Maserati Quattroporte Automatic Owner'S Manual preview
Quattroporte Automatic
Бренд: Maserati Страницы: 272
iArmor EDGE IA-N098 Quick Start Manual preview
EDGE IA-N098
Бренд: iArmor Страницы: 4
Dakota Digital MCL-7000 Series Quick Start Manual preview
MCL-7000 Series
Бренд: Dakota Digital Страницы: 2
Volvo 2010 C30 Owner'S Manual preview
2010 C30
Бренд: Volvo Страницы: 284
Draw tite 24943 Installation Instructions preview
24943
Бренд: Draw tite Страницы: 4
Mercedes-Benz CLS 280 2008 Owner'S Manual preview
CLS 280 2008
Бренд: Mercedes-Benz Страницы: 329
Broadfeet RSLX-385-68S Installation Instructions preview
RSLX-385-68S
Бренд: Broadfeet Страницы: 2
Gator GT700SD User Manual preview
GT700SD
Бренд: Gator Страницы: 6
F.lli Menabo CROSS 2 Assembly Instructions Manual preview
CROSS 2
Бренд: F.lli Menabo Страницы: 16
Mitsubishi Fuso FK 2010 Owner'S Manual preview
Fuso FK 2010
Бренд: Mitsubishi Страницы: 362
r.LiNK RL2-MMI3G-Q3 Manual preview
RL2-MMI3G-Q3
Бренд: r.LiNK Страницы: 21
Toyota Tundra guide Manual preview
Tundra guide
Бренд: Toyota Страницы: 672

Бренды по названию

Популярные бренды

Загрузить еще бренды