Suzuki GA413 Скачать руководство пользователя страница 174

Страница: 174 / 1246

LEAF SPRING FRONT BUSHING

REPLACEMENT

1) Remove leaf spring as previously outlined.
2) Remove busing with special tool and hydraulic press.

Special Tool
(A): 09951-16040
(B): 09951-46020

3) Install new bushing and then leaf spring to vehicle by reversing

removal procedure.

SPRING SHACKLE/SPRING SHACKLE
BUSHINGS (LEAF SPRING TYPE)

REMOVAL

1) Hoist vehicle.
2) Support rear axle housing by using floor jack to prevent it from

lowering.

3) Remove spring shackle nuts and remove spring shackle outer

plate.

4) Pull out spring shackle from vehicle body and leaf spring.

1. Spring shackle nuts
2. Spring shackle outer

plate

3. Spring shackle
4. Vehicle body
5. Leaf spring

5) Remove spring shackle bushings.

1. Spring shackle No.1 bushings
2. Spring shackle No.2 bushings

INSTALLATION

Reverse removal procedure for installation, noting following
points.

When installing bushing, apply soap water on its circumference
to facilitate installation.

Install spring shackle in direction as shown in figure.

Lower hoist and vehicle in non-loaded condition, tighten spring
shackle nuts to specified torque.

Tightening Torque
(a): 55 N·m (5.5 kg-m, 40.0 Ib-ft)

1. Spring shackle
2. Spring shackle outer

plate

3. Spring shackle nuts
4. Vehicle body
5. Leaf spring

3E-10

REAR SUSPENSION

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание GA413

Отзывы:

Похожие инструкции для GA413

Бренды по названию

Популярные бренды

Suzuki GA413, Руководство по обслуживанию

Результаты поиска

Содержание GA413

Отзывы:

Похожие инструкции для GA413

Бренды по названию

Популярные бренды