manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

8) Route deployment harness out the vehicle.
9) Verify that the inside of the vehicle and the area surrounding

the vehicle are clear of all people and loose or flammable ob-
jects.

10) Stretch the deployment harness to its full length 10 m (33 ft).

Special Tool
(A): 09932-75030

11) Place a power source near the shorted end of the deployment

harness. Recommended application: 12 Volts minimum, 2
amps minimum. A vehicle battery is suggested.

12) Completely cover windshield area and front door window

openings with a drop cloth, blanket to similar item. This re-
duces the possibility of injury due to possible fragmentation of
the vehicle’s glass or interior.

13) Notify all people in the immediate area that you intend to

deploy the air bag (inflator) module.

NOTE:

When the air bag deploys, the rapid gas expansion will
create a substantial report. Wear suitable ear protec-
tion. Notify all people in the immediate area that you in-
tend to deploy the air bag (inflator) module and suitable
ear protection should be worn.

After the air bag (inflator) module has been deployed,
the surface of the air bag may contain a powdery resi-
due. This powder consists primarily of cornstarch
(used to lubricate the bag as it inflates) and byproducts
of the chemical reaction.

Driver side for left hand steering vehicle

Driver side for right hand steering vehicle

1. Stretch deployment harness to its full length 10 m (33 ft).
2. Drop cloth, blanket or similar item.

WARNING:

After deployment, the metal surfaces of the air bag
(inflator) module will be very hot. Do not touch the
metal areas of them for about 30 minutes after de-
ployment.

Do not place the deployed air bag (inflator) module
near any flammable objects.

Do not apply water, oil, etc. to deployed air bag (in-
flator) module.

If the deployed air bag (inflator) module must be
moved before it is cool, wear gloves and handle it
by using nonmetal material such as the air bag and
vinyl trim.

Failure to follow procedures may result in fire or per-
sonal injury.

10B-54

AIR BAG SYSTEM

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

A-Tach Mounts 50131 Instructions preview
50131
Бренд: A-Tach Mounts Страницы: 2
WABCO TP2205 Installation Manual preview
TP2205
Бренд: WABCO Страницы: 48
Dacia 2014 Sandero Driver'S Handbook Manual preview
2014 Sandero
Бренд: Dacia Страницы: 238
AEM 30-3500 Instruction Manual preview
30-3500
Бренд: AEM Страницы: 27
Qeedon Higlow Series Product Instruction preview
Higlow Series
Бренд: Qeedon Страницы: 2
Ranger design 1525-FTR Installation Manual preview
1525-FTR
Бренд: Ranger design Страницы: 24
KEKO K162 Installation Instructions Manual preview
K162
Бренд: KEKO Страницы: 13
Road Armor Stealth 4191F Series Install Instructions preview
Stealth 4191F Series
Бренд: Road Armor Страницы: 5
TATA Motors INDICA eV2 XETA CNG Supplemental Owner'S Manual preview
INDICA eV2 XETA CNG
Бренд: TATA Motors Страницы: 24
PAC AP4-GM61 Quick Start Manual preview
AP4-GM61
Бренд: PAC Страницы: 5
Percon Falcon 655 User Manual preview
Falcon 655
Бренд: Percon Страницы: 49
Xingyun XY40EV Service Manual preview
XY40EV
Бренд: Xingyun Страницы: 74
Ford Mustang 2007 Supplement Manual preview
Mustang 2007
Бренд: Ford Страницы: 40
Ford Focus 2008 Quick Reference Manual preview
Focus 2008
Бренд: Ford Страницы: 2
V8 equipment E.BEX Manual preview
E.BEX
Бренд: V8 equipment Страницы: 34
Curt Manufacturing 58963 Installation Manual preview
58963
Бренд: Curt Manufacturing Страницы: 4
Whispbar K559W Fitting Instructions Manual preview
K559W
Бренд: Whispbar Страницы: 112
QA1 GS501 Installation Instructions preview
GS501
Бренд: QA1 Страницы: 3

Бренды по названию

Популярные бренды

Загрузить еще бренды