manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

4) Reverse removal procedure for installation.
5) Adjust generator drive belt tension, referring to BELT TEN-

SION INSPECTION in Section 6H.

6) Adjust A / C compressor belt tension, if equipped. Refer to Sec-

tion 1B.

7) Adjust intake and exhaust valve lashes as previously outlined.
8) Adjust accelerator cable play. Refer to Section 6E.
9) Check to ensure that all removed parts are back in place.

Reinstall any necessary parts which have not been reinstalled.

10) Refill cooling system and bleed air from system referring to

Section 6B.

11) Install battery and connect cables at battery.
12) Verify that there is no fuel leakage, coolant leakage and ex-

haust gas leakage at each connection.

13) Confirm that ignition timing is within specification referring to

Section 6F.

14) Connect shift control cables to gear shift control lever, refer to

GEAR SHIFT CONTROL INSTALLATION in Section 7A.

15) Perform parking brake adjustment, refer to PARKING BRAKE

INSPECTION AND ADJUSTMENT in Section 5.

16) Install engine room center member and hook front seat lock

handle securely.

ENGINE MECHANICAL

6A-47

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

GARO TWIN+ Assembly Instructions / End User Instruction preview
TWIN+
Бренд: GARO Страницы: 23
GARO LS4 Wallmounted Operational Instructions preview
LS4 Wallmounted
Бренд: GARO Страницы: 15
Conrad 75 16 30 Operating Instructions Manual preview
75 16 30
Бренд: Conrad Страницы: 26
Ford 2003 Thunderbird Owner'S Manual preview
2003 Thunderbird
Бренд: Ford Страницы: 200
Yakima K831 Manual preview
K831
Бренд: Yakima Страницы: 8
Actia SmarTach Manual preview
SmarTach
Бренд: Actia Страницы: 102
Nav TV AUDI A6 Installation Manual preview
AUDI A6
Бренд: Nav TV Страницы: 5
Dodge Ram Commercial2016 Owner'S Manual preview
Ram Commercial2016
Бренд: Dodge Страницы: 675
Cadillac 54-6219 1954 Shop Manual preview
54-6219 1954
Бренд: Cadillac Страницы: 409
Fortin THAR-AUD1 Manual preview
THAR-AUD1
Бренд: Fortin Страницы: 9
Sumitomo Dunlop L.D02.C.M Installation Manual preview
Dunlop L.D02.C.M
Бренд: Sumitomo Страницы: 22
travall TDG-1301 Fitting Instruction preview
TDG-1301
Бренд: travall Страницы: 2
Gacell 13553 User Manual preview
13553
Бренд: Gacell Страницы: 12
Jaeger 12020523 Fitting Instructions Manual preview
12020523
Бренд: Jaeger Страницы: 11
Oldsmobile 1995 Cutlass Supreme Owner'S Manual preview
1995 Cutlass Supreme
Бренд: Oldsmobile Страницы: 340
Enduro EM203 User Manual preview
EM203
Бренд: Enduro Страницы: 52
EUFAB 11512 Manual preview
11512
Бренд: EUFAB Страницы: 4
Teletrac Prism TM450 Installation Manual preview
Prism TM450
Бренд: Teletrac Страницы: 12

Бренды по названию

Популярные бренды

Загрузить еще бренды