manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

Special Tool (Air Bag Driver/Passenger Load Tool)
(B): 09932-75010

This  tool is used only when called for in this section. It is used as
a diagnostic aid and safety device to prevent inadvertent air bag
(inflator) module deployment.
The load tool has three connectors attached to its case which are
electrically functional and serve as resistive load substitutions.
No more than two connectors are used at any time.

One of connectors (“STEERING WHEEL”) is used to substitute the
load of followings.

driver air bag (inflator) module when it is connected at the top of
the column to the contact coil assembly.

passenger air bag (inflator) module when it is connected to the
air bag harness connector for passenger air bag (inflator) mod-
ule.

Another connector (“BASE OF COLUMN”) is used to substitute the
load of the driver air bag (inflator) module and the contact coil as-
sembly when it is connected at the base of the column to the air bag
wire harness.
The third connector (“PASSENGER INFLATOR”) is not used.

By substituting the resistance of the load tool when called for, a de-
termination can be made as to whether an inflator circuit compo-
nent is causing system malfunction and which component is
causing the malfunction.
The load tool should be used only when specifically called for in the
diagnostic procedures.

1. Connector for contact coil and driver air bag (inflator) mod-

ule (Located near the base of the steering column)

2. Connector for driver, passenger air bag (inflator) module

and driver and passenger seat belt pretensioners

3. Not used

AIR BAG SYSTEM

10B-7

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

N-Com B3 User Instructions And Safety preview
B3
Бренд: N-Com Страницы: 28
Feniex AM600 Instruction Manual preview
AM600
Бренд: Feniex Страницы: 6
TrailFX A4012S Installation Instructions Manual preview
A4012S
Бренд: TrailFX Страницы: 6
Mobile Create MCM3 Instruction Manual preview
MCM3
Бренд: Mobile Create Страницы: 15
femkes Hopper on Top User Manual preview
Hopper on Top
Бренд: femkes Страницы: 7
mtf TRANSPORT SYSTEM BackPower Manual preview
BackPower
Бренд: mtf TRANSPORT SYSTEM Страницы: 9
TATA Motors Indigo eCS Owner'S Manual & Service Book preview
Indigo eCS
Бренд: TATA Motors Страницы: 166
Advanced Diagnostics MVP PRO Manual preview
MVP PRO
Бренд: Advanced Diagnostics Страницы: 10
Thule 953000 Instructions Manual preview
953000
Бренд: Thule Страницы: 8
ORA XL MIRROR Installation Instructions Manual preview
XL MIRROR
Бренд: ORA Страницы: 7
Rhino-Rack S400-FK2 Instructions preview
S400-FK2
Бренд: Rhino-Rack Страницы: 2
Kuda-Phonebase 284380 Installation Instruction preview
284380
Бренд: Kuda-Phonebase Страницы: 3
VP Autoparts 419420 Installation preview
419420
Бренд: VP Autoparts Страницы: 2
Proxel EPS-DUAL Installation Instructions & User Manual preview
EPS-DUAL
Бренд: Proxel Страницы: 16
UCANDAS VDM Instruction Of Quick Operation preview
VDM
Бренд: UCANDAS Страницы: 4
HardWire HWP132A User Manual preview
HWP132A
Бренд: HardWire Страницы: 18
Honda 2012 ACCORD COUPE Owner'S Manual preview
2012 ACCORD COUPE
Бренд: Honda Страницы: 454
HOOKE ROAD BXG.8207 Quick Start Manual preview
BXG.8207
Бренд: HOOKE ROAD Страницы: 7

Бренды по названию

Популярные бренды

Загрузить еще бренды