manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

GENERAL INFORMATION ON ENGINE
SERVICE

THE FOLLOWING INFORMATION ON ENGINE SERVICE
SHOULD BE NOTED CAREFULLY, AS IT IS IMPORTANT IN
PREVENTING DAMAGE, AND IN CONTRIBUTING TO RELI-
ABLE ENGINE PERFORMANCE.

When raising or supporting engine for any reason, do not use a
jack under oil pan. Due to small clearance between oil pan and
oil pump strainer, jacking against oil pan may cause it to be bent
against strainer resulting in damaged oil pick-up unit.

It should be kept in mind, while working on engine, that 12-volt
electrical system is capable of violent and damaging short cir-
cuits.
When performing any work where electrical terminals could
possibly be grounded, ground cable of the battery should be dis-
connected at battery.

Any time the air cleaner, air intake hose, throttle body or intake
manifold is removed, the intake opening should be covered. This
will protect against accidental entrance of foreign material which
could follow intake passage into cylinder and cause extensive
damage when engine is started.

When disconnecting couplers, don’t pull wire harness but make
sure to hold coupler itself. With lock type coupler, be sure to un-
lock before disconnection. Attempt to disconnect coupler with-
out unlocking may result in damage to coupler. When
connecting lock type coupler, insert it till clicking sound is heard
and connect it securely.

Do not crank the engine for more than 15 seconds at a time. If
the engine doesn’t start on the first try, wait about 15 seconds be-
fore try again.

FUEL PRESSURE RELIEF PROCEDURE

After making sure that engine is cold, relief fuel pressure as follows.
1) Place transmission gear shift lever in “Neutral”, set parking

brake, and block drive wheels.

2) Remove fuel pump relay from main fuse box.
3) Remove fuel filler cap to release fuel vapor pressure in fuel tank

and then reinstall it.

4) Start engine and run it till it stops for lack of fuel. Repeat crank-

ing engine 2 – 3 times of about 3 seconds each time to dissipate
fuel pressure in lines. Fuel connections are now safe for servic-
ing.

5) Upon completion of servicing, install fuel pump relay to main

fuse box.

1. Fuel pump relay

CAUTION:
This work must not be done when engine is hot. If done
so, it may cause adverse effect to catalyst.

ENGINE

6-3

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

Suzuki SX4 SEDAN 2008 Owner'S Manual preview
SX4 SEDAN 2008
Бренд: Suzuki Страницы: 16
Daihatsu Mira Manual preview
Mira
Бренд: Daihatsu Страницы: 340
Zavoli Bora Technical Instructions And Installation Manual preview
Bora
Бренд: Zavoli Страницы: 26
Warrior Products 10936 Installation Instructions preview
10936
Бренд: Warrior Products Страницы: 3
RAM Ram 3500 2012 User Manual preview
Ram 3500 2012
Бренд: RAM Страницы: 116
Audiovox Prestige APS-45B Installation Manual preview
Prestige APS-45B
Бренд: Audiovox Страницы: 8
Volvo 1985 740 GL Owner'S Manual preview
1985 740 GL
Бренд: Volvo Страницы: 138
Victory 4x4 5TH GEN 4RUNNER Install Instructions preview
5TH GEN 4RUNNER
Бренд: Victory 4x4 Страницы: 5
Keith WALKING FLOOR Helpful Hints preview
WALKING FLOOR
Бренд: Keith Страницы: 2
Brodit ProClip 853660 Manual preview
ProClip 853660
Бренд: Brodit Страницы: 2
Power Fist 8985988 Manual preview
8985988
Бренд: Power Fist Страницы: 12
EAL EUFAB 16491 Operating Instructions Manual preview
EUFAB 16491
Бренд: EAL Страницы: 7
AC Schnitzer X3 M-Technik Fitting Instructions Manual preview
X3 M-Technik
Бренд: AC Schnitzer Страницы: 20
Condor T-RAMP Quick Start Manual preview
T-RAMP
Бренд: Condor Страницы: 2
Gatorback Mudflaps GCR53F Mounting Diagram & Instructions preview
GCR53F
Бренд: Gatorback Mudflaps Страницы: 4
Skoda Fabia II 2007 Workshop Manual preview
Fabia II 2007
Бренд: Skoda Страницы: 165
Maserati Grecale 2023 Owner'S Manual preview
Grecale 2023
Бренд: Maserati Страницы: 302
TOPPOINT LT95090 Quick Start Manual preview
LT95090
Бренд: TOPPOINT Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды