manualshive.com logo in svg

Suzuki GA413, Руководство по обслуживанию


Поделиться
Скачать
background image

1) Turn ignition switch to “LOCK” position, remove key and put on

safety glasses.

2) Check that there is no open, short or damage in special tool (de-

ployment harness). If any faulty is found, do not use it and be
sure to use new deployment harness.

Special Tool
(A): 09932-75030

3) Short the two deployment harness leads together by fully seat-

ing one banana plug into the other.

1. Shorted

WARNING:
Deployment harness shall remain shorted and not be
connected to a power source until the air bag is to be
deployed.

4) Remove air bag (inflator) module(s) from vehicle, referring to

SECTION 3C and 10B (if equipped with passenger air bag (in-
flator) module).

WARNING:

Always carry live air bag (inflator) module with trim
cover away from you.

When storing a live air bag (inflator) module or
when leaving a live air bag (inflator) module unat-
tended on a bench or other surface, always face the
bag and trim cover up and away from the surface.
As the live passenger air bag (inflator) module must
be placed with its bag (trim cover) facing up, place
it on the workbench with a slit or use the workbench
vise to hold it securely at its lower mounting brack-
et.
This is necessary so that a free space is provided
to allow the air bag to expand in the unlikely event
of accidental deployment.

Failure to follow procedures may result in personal in-
jury.

1. Slit on workbench
2. Workbench vise
3. Lower mounting bracket

ALWAYS CARRY AIR BAG (INFLATOR) MODULE
WITH TRIM COVER (AIR BAG OPENING) AWAY
FROM BODY.

ALWAYS PLACE AIR BAG (INFLATOR) MODULE
ON WORKBENCH WITH TRIM COVER (AIR BAG
OPENING) UP, AWAY FROM LOOSE OBJECTS.

10B-48

AIR BAG SYSTEM

Содержание GA413































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GA413

Lancia Delta Owner'S Handbook Manual preview
Delta
Бренд: Lancia Страницы: 276
T-Tech TT100 User Manual preview
TT100
Бренд: T-Tech Страницы: 38
TATA Motors Nano Owner'S Manual & Service Book preview
Nano
Бренд: TATA Motors Страницы: 94
GÄN GA Manual preview
GA
Бренд: GÄN Страницы: 24
GMC SIERRA 2019 Getting To Know Your preview
SIERRA 2019
Бренд: GMC Страницы: 20
Code 3 WingMan Installation & Operation Manual preview
WingMan
Бренд: Code 3 Страницы: 8
Metra Electronics 95-6556 Installation Instructions preview
95-6556
Бренд: Metra Electronics Страницы: 4
Rostra REARSIGHT OnStar 250-8822 Installation Instructions preview
REARSIGHT OnStar 250-8822
Бренд: Rostra Страницы: 2
Edelbrock For 1985-1992 GM Cars and Trucks 17933 Installation Instructions preview
For 1985-1992 GM Cars and Trucks 17933
Бренд: Edelbrock Страницы: 4
Rola LRSA2 Pack Contents & Fitting Instructions preview
LRSA2
Бренд: Rola Страницы: 3
Wilco Offroad UHG2060/AU Installation Manual preview
UHG2060/AU
Бренд: Wilco Offroad Страницы: 4
TATA Motors TIGOR EV 2021 Owner'S Manual preview
TIGOR EV 2021
Бренд: TATA Motors Страницы: 236
Draw tite 24943 Installation Instructions preview
24943
Бренд: Draw tite Страницы: 4
Mercedes-Benz CLS 280 2008 Owner'S Manual preview
CLS 280 2008
Бренд: Mercedes-Benz Страницы: 329
ideus VV950 User Manual preview
VV950
Бренд: ideus Страницы: 159
ULTIMATE SPEED 304669 Instructions For Use And Safety Manuallines preview
304669
Бренд: ULTIMATE SPEED Страницы: 50
U.S. General 96524 Set Up And Operating Instructions Manual preview
96524
Бренд: U.S. General Страницы: 8
Fab Fours H4550 Installation Instructions Manual preview
H4550
Бренд: Fab Fours Страницы: 13

Бренды по названию

Популярные бренды

Загрузить еще бренды